2-1/2in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 2-1/2in 2-1/4in 3-5/8in 25ft
Qty:
Qty:
Part #:810217
- 1/2" Drive SAE 3/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Part #:729-48-22-0325
- 25ft Compact Wide Blade Magnetic Tape Measure
Our Compact Wide Blade Tape Measures have up to 15' of reach allowing you to quickly take measurements. The tape is wear and impact-resistant with nylon blade protection and an additional anti-tear coating on the first 6&rdquo of the blade, reducing tape tear. Built to withstand the jobsite, the compact measuring tapes are constructed with a 5-point reinforced frame for impact resistance.
Qty:
Part #:510610
- 1" x 25" P1000 Series Yellow Clad A5 Blade Power Return Tape Measure
Crescent Lufkin® built its reputation on durability and these new tapes are no exception. The P1000 Series cases are made of tough ABS plastic, modified for increased strength and impact resistance. Every blade is protected with a clear-coat that exceeds ASTM standards for abrasion and corrosion resistance.
Qty:
Part #:810216
- 1/2" Drive SAE 5/16" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503377
- 3/4" Drive 12-Point Metric 32 mm Shallow Impact Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 and 12 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Drive end features pin retention hole and groove
Qty:
Part #:500492
- 3/4" Drive 12-Point SAE 1-3/16" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:810220
- 1/2" Drive SAE 1/2" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Part #:134-J5448H
- Proto® 6 Point Sockets are ideal for use on stubborn or damaged fasteners, and also on fasteners made from soft materials.
The TorquePlus&trade design is a high performance drive configuration which allows for quick and easy socket engagement to the fastener flats, not the corners.
The TorquePlus&trade configuration employs a radius-corner design, shifting contact area and stress away from the fastener corners and distributing contact stresses over a large area of the socket, minimizing slippage.
The TorquePlus&trade internal design minimizes fastener rounding, helps to extend fastener life, and allows the user to more easily turn worn, rounded, or rusted fasteners.
Qty:
Part #:504074
- 3/4" Drive Adapter 3/4" Female x 1/2" Male 2-1/2"
Specially heat treated for impact use to provide long life, safety, and durability
Pin and o-ring or RET RING (sold separately) secure tools onto impact wrench for safety and convenience
Suitable for use with pneumatic and electric impact wrenches
Drive end features pin retention hole and groove
Qty:
Part #:807747
- 3/4" Drive SAE 1-1/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:501675
- 1/2" Drive SAE 1/4" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:509571
- 1/2" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
closeout
$28.99 MSRP
$
26.06
Part #:500221
- CLOSEOUTS Only 21 Left!
- Crescent Lufkin 25 ft. Tape Measures, 1" Blade (Discontinued being replaced by PHV1425N)
Qty:
Part #:504375
- 1" Drive 6-Point SAE 1-5/8" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Qty:
Part #:504374
- 1" Drive 6-Point SAE 1-1/16" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:504373
- 1" Drive 6-Point SAE 1-1/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:503684
- 1/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810364
- 3/4" Drive 12-Point SAE 1-1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Displaying: 1 - 24 of 36 Matching Items