2-1/4"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Length: 2-1/4" 5" 6-7/8" 100'
Part #:810217
- 1/2" Drive SAE 3/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Part #:810216
- 1/2" Drive SAE 5/16" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503377
- 3/4" Drive 12-Point Metric 32 mm Shallow Impact Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 and 12 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Drive end features pin retention hole and groove
Qty:
Part #:500492
- 3/4" Drive 12-Point SAE 1-3/16" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:810220
- 1/2" Drive SAE 1/2" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:811830
- 1/2" Drive Impact 5" Extension
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Spring plunger provides secure socket retention for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
Qty:
Part #:810267
- 5" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:501675
- 1/2" Drive SAE 1/4" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810242
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:812781
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810313
- 5" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Part #:1184-JHWS-205P
- 1/2" Drive 5" Wobble Extension
Qty:
Part #:504374
- 1" Drive 6-Point SAE 1-1/16" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:504373
- 1" Drive 6-Point SAE 1-1/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:502826
- #1 Double Loop (Inco) Chain, Zinc Plated, 100' per Carton
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:503684
- 1/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:509575
- 1-1/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810364
- 3/4" Drive 12-Point SAE 1-1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:502077
- 1/2" Drive 12-Point SAE 1-7/16" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:502080
- 1/2" Drive 12-Point SAE 1-1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:810221
- 1/2" Drive SAE 9/16" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:510644
- 5" Industrial Grade Diagonal Cutting Pliers
&bull Handles are designed to cut wire with ease
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Induction-hardened cutting edges
&bull Regular flush cutters are used for cutting hard wire
Qty:
Displaying: 1 - 24 of 30 Matching Items