2-7/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 2-7/8in 8in 10in 16in
Qty:
Qty:
Part #:505416
- Description
CHANNELLOCK® Straight Jaw Tongue & Groove Pliers are built to last with a PERMALOCK® fastener to eliminate nut and bolt failure, patented reinforcing edge to minimize stress breakage and laser-hardened teeth to provide a better, longer lasting grip. CHANNELLOCK® Straight Jaw Tongue & Groove Pliers are made in USA and forged from high carbon U.S. steel that is specially coated for ultimate rust prevention.
The ORIGINAL STRAIGHT JAW Tongue & Groove Pliers provide a strong, versatile grip for use in both directions
RELIABLE PERMALOCK® fastener eliminates nut and bolt failure with increased joint strength
STRONG 90-degree, laser-hardened teeth for superior grip and longevity
FORGED high carbon U.S. steel for maximum strength and durability is specially coated for ultimate rust prevention.
UNDERCUT tongue & groove won&rsquot slip
CHANNELLOCK BLUE® grips for comfort
100% MADE IN USA
Qty:
Part #:505946
- Old Lang 65-(75) Snap Ring Plier:
Qty:
Part #:802246
- Description
The CHANNELLOCK® 8WCB 8" WIDEAZZ® Adjustable Wrench features a super wide jaw opening, providing the capacity of a 12-inch wrench in a lightweight, compact 8-inch adjustable wrench supporting larger nuts and bolt sizes. The combination of a smart and comfortable tapered handle design with CODE BLUE® grips, precise 4-thread knurl and minimal head width greatly improves performance in confined spaces. CHANNELLOCK® Adjustable Wrenches are made in Spain and forged from rugged chrome vanadium steel.
WIDEAZZ® jaws are up to 60% wider than a standard wrench of the same size
LONGER jaws grip better and are up to 22% THINNER than a standard wrench of the same size, providing greater access in tight spaces
MEASUREMENT SCALES are laser engraved (in. on front, mm. on reverse) and handy for sizing nuts, pipe and tube diameters
PRECISE 4-thread knurl improved adjustment accuracy
OPTIMAL head width and non-protruding jaws allow accessibility for hard to reach applications
CODE BLUE® comfort grips
RUGGED Chrome Vanadium steel construction
CHROME finish for ultimate rust prevention
Made to CHANNELLOCK® specifications in Spain.
Qty:
Part #:505945
- OLD Lang Plier Snap Ring 1434 :
Qty:
Part #:509073
- Proto Satin Combination Wrench 1/2" 12 Point
Features and Benifits
Satin finish provides corrosion resistance and a slip resistant grip.
12 point box end allows for fine indexing, helping to improve speed and access. Fits 4, 6 and 12 point fasteners.
Anti-Slip Design (ASD) open end.
Fractional sizes 11/32" and smaller and sizes 1-5/16" and larger do not have the ASD feature.
Box ends incorporate the TorquePlus&trade system.
Qty:
Part #:509041
- Proto Satin Adjustable Wrench 8-7/64"
Feature and Benefits
Satin finish provides corrosion resistance and a slip resistant grip.
Extra wide jaw capacity.
Square jaw opening provides strength and tight fit.
Rugged I-beam style handle and reinforced stress areas radius corner design.
Qty:
Part #:500550
- 3/4" Drive Extensions
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
Qty:
Qty:
Qty:
Qty:
Part #:500551
- 3/4" Drive Extensions
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
Qty:
Qty:
Part #:503697
- 5/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:810310
- 10" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:810250
- 8" Cold Chisels 1"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Qty:
Part #:811720
- 8" Combination Slip Joint Pliers Multiple parallel jaw positions are locked in to proper groove for superior non-slip performance
&bull Serrated jaws for maximum gripping power
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Shear type wire cutter extends tool use
Qty:
Qty:
Part #:802850
- 8" Mill Single Cut Second File
The Crescent Nicholson single-cut bastard mill files sharpen mill or circular saws and are ideal for draw filing and finishing metals. The rectangular shape lets you smooth and sharpen straight surfaces. 2 square edges allow you to make grooves fixed at the same width as the file, and all sizes taper slightly in width to improve access in slots.
Qty:
Part #:808433
- 10" File Card
The Crescent Nicholson file card and brush is perfect for general cleaning of file teeth, removing fillings, dirt, rust, burrs, corrosion, and most buildups of foreign material on metal. The file card and brush unclog teeth on finer cut files, allowing the abrasive to cut properly each time. Its wood base construction offers durability and ease of grip, so you can work confidently over time.
Qty:
Qty:
Displaying: 1 - 24 of 68 Matching Items