2-7/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 2-7/8in 9in 13-1/4in 16in
Qty:
Qty:
Qty:
Part #:507216
- (10)Tb 9In Prof Torpedo Lvl
High contrast e-BAND&trade vials highlight the edge of the bubble
High contrast vial surrounds improve vial visibility
3 vials - plumb, level and 45°
V-Groove working edge for accurate alignment on pipe or conduit
Aluminum frame with top read window
Strong magnetic edge
Made in the USA
Limited lifetime warranty
Qty:
Qty:
Qty:
Part #:500551
- 3/4" Drive Extensions
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
Qty:
Part #:500381
- 15/16" 12-Point SAE SUPERCOMBO® Combination Wrench
Overview
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:459-15389
- Hex End T-Handles - ProGuard&trade Finish
Solid steel handles
Welded handle/blade connection
Ergonomic handle design
Flywheel effect saves time
Smooth, non-porous handle coating
Handle coating extends along blade
Qty:
Part #:459-15390
- Hex End T-Handles - ProGuard&trade Finish
Solid steel handles
Welded handle/blade connection
Ergonomic handle design
Flywheel effect saves time
Smooth, non-porous handle coating
Handle coating extends along blade
Qty:
Part #:503697
- 5/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
closeout
Part #:511960
- CLOSEOUTS Only 1 Left!
-
3/4" x 6" Jaw & Jaw Turnbuckle, Forged Carbon Steel, Galvanized(Discontinued being replaced by TB108-J-J-HDG)
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class G
Jaws on Sizes 1/4&rdquo Through 5/8&rdquo Have Hex Head Bolt and Nut
Jaws on Sizes 3/4&rdquo Through 1-1/2&rdquo Have Cotter Key and Bolt
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
$
110.24
Qty:
closeout
Part #:511961
- CLOSEOUTS Only 4 Left!
-
3/4" x 9" Jaw & Jaw Turnbuckle, Forged Carbon Steel, Galvanized(Discontinued being replaced by TB108-9-J-J)
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class G
Jaws on Sizes 1/4&rdquo Through 5/8&rdquo Have Hex Head Bolt and Nut
Jaws on Sizes 3/4&rdquo Through 1-1/2&rdquo Have Cotter Key and Bolt
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
$
96.04
Qty:
Qty:
Part #:501513
- Country of Origin US:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:503914
- 1" Drive Extension 16"
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Hole in wall of drive end accommodates plunger for firm tool retention
Qty:
Part #:509522
- Country of Origin US:
Qty:
Displaying: 1 - 24 of 40 Matching Items