2-7/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 2-7/8in 2in 11-1/2in 23in
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:503697
- 5/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:811834
- 1/2" Drive SAE 1-1/16" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:134-J5444H
- Proto® 6 Point Sockets are ideal for use on stubborn or damaged fasteners, and also on fasteners made from soft materials.
The TorquePlus&trade design is a high performance drive configuration which allows for quick and easy socket engagement to the fastener flats, not the corners.
The TorquePlus&trade configuration employs a radius-corner design, shifting contact area and stress away from the fastener corners and distributing contact stresses over a large area of the socket, minimizing slippage.
The TorquePlus&trade internal design minimizes fastener rounding, helps to extend fastener life, and allows the user to more easily turn worn, rounded, or rusted fasteners.
Qty:
Part #:507925
- 1/4" Drive 6-Point SAE 7/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Part #:507850
- 3/4" Drive SAE 13/16" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:507852
- 3/4" Drive SAE 15/16" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:500317
- 2 to 4-3/4" SAE Adjustable Hook Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:808631
- 1" Drive 6-Point SAE 1-3/4" Impact Shallow Socket &bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener &bull Designed for maximum engagement on 6 point fasteners &bull Suitable for use with pneumatic and electric impact wrenches &bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:505666
- 1-7/16" 12-Point SAE Offset Pattern Box End Striking Wrench
Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners
Anvils are proportional to opening sizes. Special heat treating provides maximum durability for long life
Offset handle is close to head to provide clearance in confined areas
Williams' expanded line of offset striking face wrenches, up to 4-1/4", provides the most extensive line on the market
Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:811364
- 1/2" Drive 2" Extension
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Spinner disk is ideal for fast turn down of fasteners
Qty:
Part #:811412
- 1/4" Drive 2" Extension
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Packed in rugged compact high-density polyethylene (HDPE) cases that are strong and durable yet light in weight
Qty:
Displaying: 1 - 24 of 66 Matching Items