2in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 2in 5/16in 6in 9/16in
Part #:500984
- Diagonal Cutting Pliers, Tapered Nose, 6-Inch
Pliers with tapered nose are designed for working in tight spaces
Short jaws and beveled cutting edges permit close cutting of wire
Induction-hardened cutting knives for long life
Hot-riveted joint ensures smooth action and no handle wobble
Forged in the USA with custom, US-made tool steel
Plastic-dipped handles for comfort and ease of identification
Qty:
Part #:802776
- 5/16-Inch Cabinet Tip Screwdriver 1-1/2-Inch
&bull Stubby size allows for precision in tight spaces&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation&bull Precision-machined tip for exact fit&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts for added durability&bull Meets or exceeds applicable ASME / ANSI specifications
Qty:
Part #:508145
- 5/16-Inch Keystone Screwdriver, 6-Inch Square Shank
&bull Heavy-duty square shank for wrench-assisted turning&bull Bolster reinforces shank for hard use&bull Designed for the most demanding uses&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Meets or exceeds applicable ASME / ANSI specifications&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation
Qty:
Qty:
Qty:
Qty:
Part #:810216
- 1/2" Drive SAE 5/16" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:500375
- 9/16" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:500505
- 3/4" Drive 12-Point SAE 2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Qty:
Qty:
Part #:503697
- 5/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
closeout
$11.23 MSRP
$
8.95
Part #:511843
- CLOSEOUTS Only 13 Left!
-
5/16" Wire Rope Clip, Forged Carbon Steel, Galvanized (Discontinued being replace by 490-M247-2)
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:503456
- 9/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Part #:500312
- 2" SAE Adjustable Face Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:811721
- 6" Combination Slip Joint Pliers
&bull Multiple parallel jaw positions are locked in to proper groove for superior non-slip performance
&bull Serrated jaws for maximum gripping power
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Shear type wire cutter extends tool use
Qty:
Part #:811597
- 3/8" Drive 6-Point SAE 9/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:508016
-
5/16" Grade 30 Proof Coil Chain, Zinc Plated, 92' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Part #:812781
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Displaying: 25 - 48 of 173 Matching Items