1-3/4in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 1-3/4in 3/16 in 13MM 17MM
Part #:502912
-
3/16&rdquo Cold Shut, Steel, Zinc Plated
Connections for Chain and Attachments
When Using Cold Shuts with Chain, Use One Size Larger Than Chain Size
With A Hammer, Drive the Open End Through the Cold Shut Eye. Peen the Extended End to Prevent Opening
Order Unit is "Each"
Note Cold Shuts Should Not Be Reused After Closure Has Been Made
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Qty:
Qty:
Part #:729-5446-21
- 1-3/4" SDS Max Demolition Hammer
Get best-in-class power and the highest overload protection for the toughest demolition jobs. The SDS-Max Demolition Hammer has a heavy-duty crank piston mechanism that delivers 8.8 ft-lbs of impact energy for hard-hitting performance in any concrete. For lighter applications, the two-speed impact mode allows you to reduce BPM to 2,200. Advanced Constant Power Technology electronics and a mechanical clutch enhance your control and the demolition hammer&rsquos long-term durability. The Anti-Vibration System and side D-handle ensure safe, comfortable use. The tool comes with a carrying case.
Qty:
Part #:508171
- 1" Drive 12-Point SAE 1-3/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:502805
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:508012
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511937
-
3/16" Wire Rope Thimble, Electro-Galvanized
If Used on Coated Cable, Remove the Coating From the Assembly Area
Follow Assembly Instructions
Qty:
Part #:811853
- 1-3/4" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:808631
- 1" Drive 6-Point SAE 1-3/4" Impact Shallow Socket &bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener &bull Designed for maximum engagement on 6 point fasteners &bull Suitable for use with pneumatic and electric impact wrenches &bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Qty:
Part #:504437
- 1-3/4" 12-Point SAE Offset Pattern Box End Striking Wrench
Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners
Anvils are proportional to opening sizes. Special heat treating provides maximum durability for long life
Offset handle is close to head to provide clearance in confined areas
Williams' expanded line of offset striking face wrenches, up to 4-1/4", provides the most extensive line on the market
Specifically engineered to hold up under the most rigorous industrial use
Qty:
Qty:
Part #:500502
- 3/4" Drive 12-Point SAE 1-3/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:513132
- 13 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:513136
- 17 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:806809
-
3/16" Quick Link, Steel, Zinc Plated, #7350
For Fast and Easy Connections Between Two Lengths of Chain
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Do Not Use to Support Human Weight, for Playground or Athletic Equipment, or as a Safety Device
Qty:
Part #:729-49-59-1750
- 1-3/4" x 1" Annular Cutter
Dual alternating tooth geometry and thin-wall construction help Milwaukee&rsquos Annular Cutter cut up to 15% faster than the competition. With 20% thinner walls, the cutter displaces less material for the same size hole, giving you fast, burr-free holes in anything from sheet metal to thick steel plate.Milwaukee&rsquos proprietary high-speed steel with three hardness zones minimizes breakage and helps the bit last longer. It comes with a 3/4&rdquo Weldon shank, which is ideal for use with most small magnetic drill presses and large magnetic drill presses with the correct arbor.
Qty:
Part #:271822
- Business Unit Tools. Product Level 1 Tools M18. Product Level 2 Tools Hammers. Product Level 3 TOL SDS Max. Product Level 4 TOL SDS Max/Spline Hammers. Product Level 5 TOL FUEL ONE-KEY. AX Item Number 271822HD. Country of Origin CHN. Harmonized Tariff 8467290080.:
Qty:
Qty:
Part #:134-J5441-17M
- Country of Origin United States:
Qty:
Displaying: 1 - 24 of 25 Matching Items