1/4in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 1/4in 3/16 in 5/8in
Part #:502912
-
3/16&rdquo Cold Shut, Steel, Zinc Plated
Connections for Chain and Attachments
When Using Cold Shuts with Chain, Use One Size Larger Than Chain Size
With A Hammer, Drive the Open End Through the Cold Shut Eye. Peen the Extended End to Prevent Opening
Order Unit is "Each"
Note Cold Shuts Should Not Be Reused After Closure Has Been Made
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Qty:
Part #:508013
-
1/4" Grade 30 Proof Coil Chain, Zinc Plated, 141' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Part #:511896
-
5/8" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Part #:806806
-
1/4" Quick Link, Steel, Zinc Plated, #7350
For Fast and Easy Connections Between Two Lengths of Chain
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Do Not Use to Support Human Weight, for Playground or Athletic Equipment, or as a Safety Device
Qty:
Qty:
Part #:729-2401-20
- M12&trade 1/4" Hex Screwdriver (Tool Only)
Optimized for the professional who frequently encounters precision fastening applications, the Milwaukee® M12&trade ¼&rdquo Hex Screwdriver delivers unmatched precision, power and portability along with a slimmer, more ergonomic grip. A variable speed trigger and 0-500RPM give the user unrivaled fastening control, 15+1 clutch settings prevent over tightening fasteners, and 175 in-lbs. of torque provides the ability to accomplish tough applications. At 6-1/2 in. long and weighing only 2.0lbs its compact, lightweight and durable design provides greater comfort and fits in tighter spaces on the jobsite. The onboard LED light and fuel gauge help you increase productivity and avoid interruptions. Two belt-clip positions for both left- and right-handed users and one-handed bit changes provide maximum ease-of-use. The REDLITHIUM&trade Battery Pack delivers more work per charge and more work over pack life than the competitors.
Qty:
Qty:
Qty:
Part #:134-J86058
- Made from S2 steel and specially heat-treated for greater strength and durability.
Hand-ground cutting edge to the exact angle for cutting through tough metals.
20% larger striking surface than standard chisels directs the power to the cutting edge.
Longer shank features a knurl for better grip and easy positioning.
Black oxide finish to help prevent rust corrosion extending tool life and performance.
Qty:
Qty:
Part #:521217
- JAT-401, 1/4" Die Grinder
The JAT-401 1/4'' Die Grinder features a powerful motor and aluminum housing. Built with durability in mind, this tool will withstand the daily grind you need to get your job done.
Qty:
Qty:
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503696
- 1/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:502805
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:502806
-
1/4" Grade 30 Proof Coil Chain, Zinc Plated, 800' per Round Drum
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:504834
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:504841
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:508012
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511891
-
1/4" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Part #:511910
-
1/4" Clevis Grab Hook
Material is
Zinc Plated Hooks Are Packed 10 Per Box
Grab Hooks Are Designed to Grab a Chain Link and Hold it in Place
Hooks are Sized by the Material Diameter of the Chain That They Engage. Make Sure the Hook Size and Chain Diameter are Compatible Before Attaching to Load
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Displaying: 1 - 24 of 160 Matching Items