3-3/8"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Length: 3-3/8" 6-7/8" 9" 18"
Qty:
Part #:507216
- (10)Tb 9In Prof Torpedo Lvl
High contrast e-BAND&trade vials highlight the edge of the bubble
High contrast vial surrounds improve vial visibility
3 vials - plumb, level and 45°
V-Groove working edge for accurate alignment on pipe or conduit
Aluminum frame with top read window
Strong magnetic edge
Made in the USA
Limited lifetime warranty
Qty:
Part #:503577
- 18" Heavy Duty Roll Bars
Aligning and prybar with long tapered body and 90 rolling head
Qty:
closeout
Part #:511960
- CLOSEOUTS Only 1 Left!
-
3/4" x 6" Jaw & Jaw Turnbuckle, Forged Carbon Steel, Galvanized(Discontinued being replaced by TB108-J-J-HDG)
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class G
Jaws on Sizes 1/4&rdquo Through 5/8&rdquo Have Hex Head Bolt and Nut
Jaws on Sizes 3/4&rdquo Through 1-1/2&rdquo Have Cotter Key and Bolt
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
$
110.24
Qty:
closeout
Part #:511961
- CLOSEOUTS Only 5 Left!
-
3/4" x 9" Jaw & Jaw Turnbuckle, Forged Carbon Steel, Galvanized(Discontinued being replaced by TB108-9-J-J)
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class G
Jaws on Sizes 1/4&rdquo Through 5/8&rdquo Have Hex Head Bolt and Nut
Jaws on Sizes 3/4&rdquo Through 1-1/2&rdquo Have Cotter Key and Bolt
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
$
96.04
Qty:
Qty:
Qty:
Part #:501426
- 1" Drive 12-Point SAE 2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:810357
- 3/4" Drive 12-Point SAE 2-1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:506842
-
Overview
&bull Includes 5 bits 2 slotted, #1 Phillips®, #2 Phillips®, and T-15 Torx®
&bull Ergonomically designed handle for greater user comfort and control
&bull Hi-impact plastic handle for durability and flexibility in all types of work applications
&bull Heavy-duty 3-way On-Off-Locked ratcheting mechanism allows consistent and smooth operation
&bull Powerful magnetic shank securely holds bit in place before, during and after the job application
&bull Stainless steel shank eliminates problems of chrome chipping or rust
&bull Easy bit storage in handle
&bull Accepts all standard 1/4" hex shank bits
Qty:
Qty:
Part #:810536
- 18" Metal Socket Set Toolbox
Ruggedly constructed for long life
Ideal for storing socket sets, other tools, and small parts
Made from cold-rolled steel
Qty:
Part #:509575
- 1-1/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:501966
- 18" Extra-Long 3/4" Flat Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:806427
- 3/8" Drive Speeder Handle 18"
&bull Chrome plating provides increased protection from rust and corrosion
&bull Drive handles provide extra leverage with greater strength than ratchets
&bull Speeder handle is ideal for fast turn down of fasteners
Qty:
Part #:810307
- 9" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
closeout
$11.00 MSRP
$
6.93
Part #:507699
- CLOSEOUTS Only 2 Left!
- Being Replaced by
Proto® DuraTek&trade Phillips Round Bar Screwdriver - # 1 x 3"
ITEM #JP0103R
Qty:
Part #:729-48-62-2010
- SPL/RDHEX Demo 18" Bull Point
Milwaukee® Spline or Round/Hex Standard Chisels are made of drop forged high grade steel. These chisels are specifically designed for spline rotary hammers and should be used in hammer only mode.
Qty:
Part #:729-48-62-2030
- SPL/RDHEX Demo 1" x 18" Flat Chisel
Milwaukee® Spline or Round/Hex Standard Chisels are made of drop forged high grade steel. These chisels are specifically designed for spline rotary hammers and should be used in hammer only mode.
Qty:
Qty:
Part #:729-48-20-7256
- 1-1/8" Bit,18" Bit,SDS+,TE-CX,4-Cutter,:
Qty:
Part #:729-48-20-7357
- Country of Origin DEU:
Qty:
Part #:729-48-20-7377
- Country of Origin DEU:
Qty:
Qty:
Displaying: 1 - 24 of 28 Matching Items