3-7/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 3-7/8in 11-1/2in 16in 25ft
Qty:
Qty:
Part #:729-48-22-0325
- 25ft Compact Wide Blade Magnetic Tape Measure
Our Compact Wide Blade Tape Measures have up to 15' of reach allowing you to quickly take measurements. The tape is wear and impact-resistant with nylon blade protection and an additional anti-tear coating on the first 6&rdquo of the blade, reducing tape tear. Built to withstand the jobsite, the compact measuring tapes are constructed with a 5-point reinforced frame for impact resistance.
Qty:
Qty:
Part #:510610
- 1" x 25" P1000 Series Yellow Clad A5 Blade Power Return Tape Measure
Crescent Lufkin® built its reputation on durability and these new tapes are no exception. The P1000 Series cases are made of tough ABS plastic, modified for increased strength and impact resistance. Every blade is protected with a clear-coat that exceeds ASTM standards for abrasion and corrosion resistance.
Qty:
Part #:500551
- 3/4" Drive Extensions
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
Qty:
Qty:
Part #:502010
- 3 7/8" Center Punches 1/4"
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Part #:501513
- Country of Origin US:
Qty:
Qty:
closeout
$28.99 MSRP
$
26.06
Part #:500221
- CLOSEOUTS Only 21 Left!
- Crescent Lufkin 25 ft. Tape Measures, 1" Blade (Discontinued being replaced by PHV1425N)
Qty:
Qty:
Qty:
Part #:512743
- Country of Origin US:
Qty:
Part #:503914
- 1" Drive Extension 16"
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Hole in wall of drive end accommodates plunger for firm tool retention
Qty:
Part #:500317
- 2 to 4-3/4" SAE Adjustable Hook Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:505666
- 1-7/16" 12-Point SAE Offset Pattern Box End Striking Wrench
Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners
Anvils are proportional to opening sizes. Special heat treating provides maximum durability for long life
Offset handle is close to head to provide clearance in confined areas
Williams' expanded line of offset striking face wrenches, up to 4-1/4", provides the most extensive line on the market
Specifically engineered to hold up under the most rigorous industrial use
Qty:
Qty:
Part #:513141
- 20 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:503590
- 16" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:501707
- 16" Heavy Duty Pinch Bars
Used for aligning, prying and positioning
Qty:
Qty:
Qty:
Part #:729-48-22-0225M
- Country of Origin VNM:
Qty:
Displaying: 1 - 24 of 25 Matching Items