4-3/4in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 4-3/4in 6-3/4in 10in 12-7/8in
Qty:
Part #:505416
- Description
CHANNELLOCK® Straight Jaw Tongue & Groove Pliers are built to last with a PERMALOCK® fastener to eliminate nut and bolt failure, patented reinforcing edge to minimize stress breakage and laser-hardened teeth to provide a better, longer lasting grip. CHANNELLOCK® Straight Jaw Tongue & Groove Pliers are made in USA and forged from high carbon U.S. steel that is specially coated for ultimate rust prevention.
The ORIGINAL STRAIGHT JAW Tongue & Groove Pliers provide a strong, versatile grip for use in both directions
RELIABLE PERMALOCK® fastener eliminates nut and bolt failure with increased joint strength
STRONG 90-degree, laser-hardened teeth for superior grip and longevity
FORGED high carbon U.S. steel for maximum strength and durability is specially coated for ultimate rust prevention.
UNDERCUT tongue & groove won&rsquot slip
CHANNELLOCK BLUE® grips for comfort
100% MADE IN USA
Qty:
Part #:505946
- Old Lang 65-(75) Snap Ring Plier:
Qty:
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Part #:513127
- 10 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:810310
- 10" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:503706
- 1" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810266
- 4 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Qty:
Part #:503867
- 8" Flat Magicut® File
The Crescent Nicholson flat Magicut® file with American pattern is ideal for machinists and removes stock rapidly for a fast and efficient application. The rectangular shape allows you to smooth and sharpen straight surfaces. The narrow chip breaker pattern created by steep, angled serrations helps quickly remove material and provides a smoother finish. The slight taper in width towards the file's point creates ease of access in slots.
Qty:
Part #:505986
- 8" Mill Single Cut Smooth File
The Crescent Nicholson single-cut bastard mill files sharpen mill or circular saws and are ideal for draw filing and finishing metals. The rectangular shape lets you smooth and sharpen straight surfaces. 2 square edges allow you to make grooves fixed at the same width as the file, and all sizes taper slightly in width to improve access in slots.
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Displaying: 1 - 24 of 42 Matching Items