4-3/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 4-3/8in 8in 24in 100ft
Part #:500566
- #2 Twist Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility Applications
Standard Material Low Carbon Steel
Standard Finish Bright, Zinc Plated and Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Qty:
Qty:
Part #:802246
- Description
The CHANNELLOCK® 8WCB 8" WIDEAZZ® Adjustable Wrench features a super wide jaw opening, providing the capacity of a 12-inch wrench in a lightweight, compact 8-inch adjustable wrench supporting larger nuts and bolt sizes. The combination of a smart and comfortable tapered handle design with CODE BLUE® grips, precise 4-thread knurl and minimal head width greatly improves performance in confined spaces. CHANNELLOCK® Adjustable Wrenches are made in Spain and forged from rugged chrome vanadium steel.
WIDEAZZ® jaws are up to 60% wider than a standard wrench of the same size
LONGER jaws grip better and are up to 22% THINNER than a standard wrench of the same size, providing greater access in tight spaces
MEASUREMENT SCALES are laser engraved (in. on front, mm. on reverse) and handy for sizing nuts, pipe and tube diameters
PRECISE 4-thread knurl improved adjustment accuracy
OPTIMAL head width and non-protruding jaws allow accessibility for hard to reach applications
CODE BLUE® comfort grips
RUGGED Chrome Vanadium steel construction
CHROME finish for ultimate rust prevention
Made to CHANNELLOCK® specifications in Spain.
Qty:
Part #:505945
- OLD Lang Plier Snap Ring 1434 :
Qty:
Part #:509073
- Proto Satin Combination Wrench 1/2" 12 Point
Features and Benifits
Satin finish provides corrosion resistance and a slip resistant grip.
12 point box end allows for fine indexing, helping to improve speed and access. Fits 4, 6 and 12 point fasteners.
Anti-Slip Design (ASD) open end.
Fractional sizes 11/32" and smaller and sizes 1-5/16" and larger do not have the ASD feature.
Box ends incorporate the TorquePlus&trade system.
Qty:
Part #:502824
-
2/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Carton
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:509041
- Proto Satin Adjustable Wrench 8-7/64"
Feature and Benefits
Satin finish provides corrosion resistance and a slip resistant grip.
Extra wide jaw capacity.
Square jaw opening provides strength and tight fit.
Rugged I-beam style handle and reinforced stress areas radius corner design.
Qty:
Part #:500550
- 3/4" Drive Extensions
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
Qty:
Qty:
Qty:
Part #:502825
-
1/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Reel
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Polycoated in White, Yellow, Green or Red Colors
Design Factor 4 to 1
Packaged on Reels, Order Unit is "Each"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Part #:810250
- 8" Cold Chisels 1"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:509570
- 5/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:811720
- 8" Combination Slip Joint Pliers Multiple parallel jaw positions are locked in to proper groove for superior non-slip performance
&bull Serrated jaws for maximum gripping power
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Shear type wire cutter extends tool use
Qty:
Part #:500763
- 3/8" x 100' Banner® Yellow Clad Tape Measure
The Crescent Banner Tape Measure has a rugged, vinyl-covered steel case. Its large easy action winding drum and nylon rollers prevent friction for a easy rewind. The tape has a 2-in-1 endhook that allows users to grasp on to what ever is available.
Qty:
Qty:
Qty:
Part #:509622
- 100' Nylon Fishtape
Non-conductive, curl resistant nylon tape for fast, clean fishing
Good for fishing in conduit with wire or cable present
Rugged case design improves drop impact capability
Advanced comfort handle grip reduces fatigue
Nylon fish tape is intended for fishing only
Rope or line is recommended for pulling
Qty:
Part #:500934
- 100' REEL-X Non-Conductive Fish Tape
Free-spinning interior reel for faster fishing
Utilize secondary exit and set case on the ground to free-up both hands for fishing
Anti-Bind Design
Quick-Change replacement reels
Fatigue/Strain reducing ergonomic case design
Bulk Pack Available (Qty 3) - FTXF-100BP
Compatible Replacement Reels RFTXF-50, RFTXF-100
Qty:
Part #:917-62605
- ONE-PIECE FLAT SEWER TAPE&bull Sizes and lengths for use on sewer and drain lines through 8" (200 mm) in diameter and up to 100'(30,4 m) in length.&bull Carrier included with all except 25' (7,6 m) model.&bull All models have a hand grip and a spear point at one end and roller ball at the othe
Qty:
Displaying: 1 - 24 of 48 Matching Items