3-5/8"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Length: 3-5/8" 4" 12" 1.9"
Qty:
Qty:
Part #:812981
- 12" Extra-Long Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810311
- 12" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:509571
- 1/2" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
closeout
$43.28 MSRP
$
24.70
Part #:511954
- CLOSEOUTS Only 4 Left!
-
1/4&rdquo x 4&rdquo Hook & Eye Turnbuckle, Forged Carbon Steel, Galvanized
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class F
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:521078
- Bit Extension 12"
Extend your reach when drilling with Milwaukee Selfeed Bits, Auger Bits and Hole Saws. Accepts all 7/16 inch hex, secures with a hex key included. The 7/16 inch hex fits both 3 jawed chucks, 1/2 inch drill capacity and larger, as well as 7/16 inch Quick Change chucks.
Qty:
Part #:521077
- 12" x 1/4" Universal QUIK-LOK&trade Extension
The 1/4" Universal QUIK-LOK&trade Extension has an innovative design that fits all 1/4" shanks - with or without a power-groove. The unique design requires no tools to change out bits, making it fast and efficient.
Qty:
Qty:
Part #:504375
- 1" Drive 6-Point SAE 1-5/8" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:501446
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:504806
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Qty:
Part #:810263
- 12" Extra-Long Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:501960
- 12" Extra-Long Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:729-48-62-2050
- 2" Scaling Chisel
Milwaukee® Spline or Round/Hex Standard Chisels are made of drop forged high grade steel. These chisels are specifically designed for spline rotary hammers and should be used in hammer only mode.
Qty:
Part #:729-48-32-4512
- SHOCKWAVE&trade Impact Magnetic Bit Holder
Our SHOCKWAVE&trade Impact Duty&trade Magnetic Bit Holders are engineered for extreme durability and up to 30x life. The MILWAUKEE magnetic bit holders are made from proprietary steel, heat treated to control hardness. The SHOCKWAVE&trade magnetic bit holders feature a powerful magnet, providing you with a secure grip and unyielding bit engagement. Each bit holder has a 2-piece construction for optimal assembly in abusive applications. Our SHOCKWAVE&trade Impact Duty&trade Magnetic Bit Holders can now be used with with Milwaukee SHOCKWAVE&trade Impact Duty Insert Magnetic Nut Drivers (¼&rdquo, 5/16&rdquo, &rdquo, 7/16&rdquo, ½&rdquo).
Qty:
Part #:729-E250IM
- Business Unit Hand Tools, Storage, PPE. Product Level 1 HT|S|PPE-Layout. Product Level 2 HT|S|PPE-Squares. Product Level 3 HT Combo Squares. Product Level 4 HT IM Squares. Product Level 5 HT Empire. AX Item Number E250IM. Country of Origin USA. Harmonized Tariff 9017208080.:
Qty:
Part #:729-E250
- 12" Professional Combination Square
BLADE-LOCK&trade for fast adjustment and secure hold
DUAL-PITCH&trade vial for checking 1 and 2 degree slope
Rational Head Dimensions
Heavy duty machined head for guaranteed accuracy
Scriber pin stored on board for convenient marking of materials
High visibility chemical etched stainless steel blade
Made in the USA with global materials
Limited lifetime warranty
Qty:
Part #:729-48-20-7203
- Country of Origin DEU:
Qty:
Part #:729-48-20-7434
- Country of Origin DEU:
Qty:
Part #:729-48-20-7335
- Country of Origin DEU:
Qty:
Part #:729-48-03-3540
- Spline Thin Wall Core Bit 12" Adapter Shank
Qty:
Part #:729-48-03-3564
- Spline Thick Wall Core Bit 12" Adapter Shank
Qty:
Displaying: 1 - 24 of 25 Matching Items