4"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Length: 4" 5" 11-1/2" 2.4"
Qty:
Part #:811830
- 1/2" Drive Impact 5" Extension
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Spring plunger provides secure socket retention for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
Qty:
Part #:810267
- 5" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:810242
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:812781
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810313
- 5" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
closeout
$43.28 MSRP
$
24.70
Part #:511954
- CLOSEOUTS Only 4 Left!
-
1/4&rdquo x 4&rdquo Hook & Eye Turnbuckle, Forged Carbon Steel, Galvanized
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class F
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:1184-JHWS-205P
- 1/2" Drive 5" Wobble Extension
Qty:
Part #:500317
- 2 to 4-3/4" SAE Adjustable Hook Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:505666
- 1-7/16" 12-Point SAE Offset Pattern Box End Striking Wrench
Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners
Anvils are proportional to opening sizes. Special heat treating provides maximum durability for long life
Offset handle is close to head to provide clearance in confined areas
Williams' expanded line of offset striking face wrenches, up to 4-1/4", provides the most extensive line on the market
Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:501451
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:504812
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Qty:
Part #:513141
- 20 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:510644
- 5" Industrial Grade Diagonal Cutting Pliers
&bull Handles are designed to cut wire with ease
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Induction-hardened cutting edges
&bull Regular flush cutters are used for cutting hard wire
Qty:
Part #:509837
- 1/4" Drive Round Head Ratchet 5"
Double pawl design with 72 teeth action provides a 5 ratcheting angle
Shift lever reverses action instantly
Knurled handle provides a non-slip grip
Chrome plating provides increased protection from rust and corrosion
Qty:
Part #:500540
- 1/2" Drive 5" Extension
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Spinner disk is ideal for fast turn down of fasteners
Qty:
Displaying: 1 - 17 of 17 Matching Items