4mm
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 4mm 7/16in 9/32in 24in
Qty:
Part #:808044
- ALUMINUM STRAIGHT PIPE WRENCHES&bull RIDGID® Aluminum Pipe Wrenches provide professional strength inlightweight aluminum. The Aluminum Straight Pipe Wrench offersthe same durability and ease-of-use found in all RIDGID heavy-dutywrenches.
3" Pipe Capacity
Qty:
Part #:510617
- 24" Industrial Grade Center Cut Cutter
Since 1880, Crescent H.K. Porter has been the preeminent brand in industrial cutters with a worldwide reputation for quality, strength, and durability. The extensive line of products includes manual cutters, pneumatic cutters, and accessories, designed to handle everything from light wires and brushes to heavy steel rods and bars.
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:501590
- 1/2" Drive SAE 5/8" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Part #:503701
- Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
closeout
$12.46 MSRP
$
7.11
Part #:511845
- CLOSEOUTS Only 5 Left!
-
7/16" Wire Rope Clip, Forged Carbon Steel, Galvanized (Being replaced by Columbus Mckinnon 2/Pack 490-M249-2)
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:507925
- 1/4" Drive 6-Point SAE 7/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Qty:
Part #:508072
- HEAVY-DUTY OFFSET PIPE WRENCHES&bull Heavy-Duty Offset Pipe Wrenches feature a jaw opening parallel tothe handle and a narrower hook jaw head. Provides easy entry intotight spots.
3" Pipe Capacity
Qty:
Part #:811645
- 1/2" Drive 6-Point SAE 7/16" Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
closeout
$41.25 MSRP
$
27.64
Part #:506620
- CLOSEOUTS Only 7 Left!
-
9/32" Quik-Alloy® Sling Hook w/Latch, Grade 100, Painted Green
For Use with Grade 80/100 Chain Slings
4 to 1 Design Factor
Meet or Exceed All Requirements of ASME B30.9 and B30.10
100% Proof Tested in Accordance with ASTM A952
Additionally Hallmarked with "USA" and Date Code
Made in the USA
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511894
-
7/16" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:507160
- HEAVY-DUTY STRAIGHT PIPE WRENCHES&bull Straight Pipe Wrenches have a sturdy, ductile-iron housing and anI-beam handle with a full floating forged hook jaw, featuring selfcleaningthreads with replaceable hook and heel jaws.&bull Heavy-duty pipe wrenches comply with federal specifications GGGW65IE,Type II, Class A.
3" Pipe Capacity
Qty:
Qty:
Displaying: 1 - 24 of 64 Matching Items