2-7/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 2-7/8in 5-3/8in 5in 200ft
Qty:
Qty:
Part #:503697
- 5/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Part #:811830
- 1/2" Drive Impact 5" Extension
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Spring plunger provides secure socket retention for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
Qty:
Qty:
Part #:810242
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Qty:
Part #:810267
- 5" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:507375
-
2/0 Passing Link Chain, Zinc Plated, 200' per Square Pail
Uses General Utility, Animal, and Farm and Ranch Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Part #:812781
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810313
- 5" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Qty:
Qty:
Part #:500315
- 3/4 to 2" SAE Adjustable Hook Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:808631
- 1" Drive 6-Point SAE 1-3/4" Impact Shallow Socket &bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener &bull Designed for maximum engagement on 6 point fasteners &bull Suitable for use with pneumatic and electric impact wrenches &bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Qty:
Part #:1184-JHWS-205P
- 1/2" Drive 5" Wobble Extension
Qty:
Qty:
Part #:810360
- 1" Drive 12-Point SAE 1-5/8" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:500540
- 1/2" Drive 5" Extension
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Spinner disk is ideal for fast turn down of fasteners
Qty:
Part #:500503
- 3/4" Drive 12-Point SAE 1-13/16" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Displaying: 1 - 24 of 33 Matching Items