5"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Length: 5" 6-3/4" 10'
Qty:
Qty:
Qty:
Qty:
Part #:811830
- 1/2" Drive Impact 5" Extension
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Spring plunger provides secure socket retention for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
Qty:
Part #:810242
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:513127
- 10 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:810267
- 5" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:503706
- 1" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:812781
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810313
- 5" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Part #:1184-JHWS-205P
- 1/2" Drive 5" Wobble Extension
Qty:
Qty:
Part #:500540
- 1/2" Drive 5" Extension
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Spinner disk is ideal for fast turn down of fasteners
Qty:
Part #:509837
- 1/4" Drive Round Head Ratchet 5"
Double pawl design with 72 teeth action provides a 5 ratcheting angle
Shift lever reverses action instantly
Knurled handle provides a non-slip grip
Chrome plating provides increased protection from rust and corrosion
Qty:
Part #:510644
- 5" Industrial Grade Diagonal Cutting Pliers
&bull Handles are designed to cut wire with ease
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Induction-hardened cutting edges
&bull Regular flush cutters are used for cutting hard wire
Qty:
Part #:505336
- 1/2 X 9/6" 12-Point Number of Points Double Head Ratcheting Box Wrench
Allows fast removal of fasteners with a ratcheting action at each end
Ideal for long bolt-through applications
Flat handle allows access to tight clearance areas
Turn wrench over to change direction
Qty:
Part #:729-48-76-5010
- 10' 2-Wire QUIK-LOK® Cord
This Milwaukee QUIK-LOK® cord is a two wire double insulated 10 foot cord for fast field replacement of a damaged cord. Made of premium grade Hi-Flex wire the cord is quickly removed and attached to Milwaukee tools with the QUIK-LOK® cord feature. To change a damaged cord simply turn the collar at the top of the cord counter clockwise to loosen the nut and pull down on the cord to remove. To re-attach a new cord, line up the pins in the end of the tool with the pin receptacles in the end of the cord, push together and turn the collar clockwise to lock in place. Cord has a 1-15P NEMA type plug.
Qty:
Displaying: 1 - 18 of 18 Matching Items