7"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Length: 7" 9" 11-1/2" 35"
Qty:
Part #:811713
- 7" Needle Nose Pliers
Polished heads resist rust and corrosion, extending the tool life
Serrated jaws provide extra gripping power
The PL-114CS short nose model is supplied with a spring and is designed for close, fine electrical and mechanical work
The PL-116C long nose model provides excellent gripping ability for use in tight, narrow places
Qty:
Part #:507216
- (10)Tb 9In Prof Torpedo Lvl
High contrast e-BAND&trade vials highlight the edge of the bubble
High contrast vial surrounds improve vial visibility
3 vials - plumb, level and 45°
V-Groove working edge for accurate alignment on pipe or conduit
Aluminum frame with top read window
Strong magnetic edge
Made in the USA
Limited lifetime warranty
Qty:
Part #:501137
- 7" Industrial Grade Linesman's Pliers
&bull Designed for wiring, electrical equipment installation and maintenance for utility linemen
&bull Polished faces look good and resist corrosion
&bull Induction-hardened cutting edges stay sharp longer
&bull Diamond serrated jaws provide solid grip on wire
&bull Double-dipped plastic handle grips are comfortable yet durable
Qty:
Part #:501440
- 7" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Qty:
Part #:812965
- 7" Industrial Grade Diagonal Cutting Pliers
&bull Handles are designed to cut wire with ease
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Induction-hardened cutting edges
&bull Regular flush cutters are used for cutting hard wire
Qty:
closeout
$89.89 MSRP
$
72.25
Part #:501867
- CLOSEOUTS Only 1 Left!
- Country of Origin US:
Qty:
closeout
$187.74 MSRP
$
110.24
Part #:511960
- CLOSEOUTS Only 1 Left!
-
3/4" x 6" Jaw & Jaw Turnbuckle, Forged Carbon Steel, Galvanized(Discontinued being replaced by TB108-J-J-HDG)
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class G
Jaws on Sizes 1/4&rdquo Through 5/8&rdquo Have Hex Head Bolt and Nut
Jaws on Sizes 3/4&rdquo Through 1-1/2&rdquo Have Cotter Key and Bolt
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
closeout
$168.18 MSRP
$
96.04
Part #:511961
- CLOSEOUTS Only 5 Left!
-
3/4" x 9" Jaw & Jaw Turnbuckle, Forged Carbon Steel, Galvanized(Discontinued being replaced by TB108-9-J-J)
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
Meets Design Requirements of ASTM F1145, Type 1, Grade 1, Class G
Jaws on Sizes 1/4&rdquo Through 5/8&rdquo Have Hex Head Bolt and Nut
Jaws on Sizes 3/4&rdquo Through 1-1/2&rdquo Have Cotter Key and Bolt
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Qty:
Qty:
Part #:506842
-
Overview
&bull Includes 5 bits 2 slotted, #1 Phillips®, #2 Phillips®, and T-15 Torx®
&bull Ergonomically designed handle for greater user comfort and control
&bull Hi-impact plastic handle for durability and flexibility in all types of work applications
&bull Heavy-duty 3-way On-Off-Locked ratcheting mechanism allows consistent and smooth operation
&bull Powerful magnetic shank securely holds bit in place before, during and after the job application
&bull Stainless steel shank eliminates problems of chrome chipping or rust
&bull Easy bit storage in handle
&bull Accepts all standard 1/4" hex shank bits
Qty:
Part #:500317
- 2 to 4-3/4" SAE Adjustable Hook Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:811885
- 3/4" Drive 7" Impact Extension
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Pin and o-ring or RET RING® (sold separately) secure tools onto impact wrench for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Drive end features pin retention hole and groove
Qty:
Part #:505666
- 1-7/16" 12-Point SAE Offset Pattern Box End Striking Wrench
Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners
Anvils are proportional to opening sizes. Special heat treating provides maximum durability for long life
Offset handle is close to head to provide clearance in confined areas
Williams' expanded line of offset striking face wrenches, up to 4-1/4", provides the most extensive line on the market
Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:509576
- 3/8 X 3" Nutdriver Cushion GRIP
Hollow shaft accommodates long bolts or studs
Precision machined socket end
Cushion grip handle for comfort
Size imprinted on color coded ends for easy identification
Qty:
Part #:513141
- 20 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:810302
- 7/16 X 3" Nutdriver Cushion Grip
Hollow shaft accommodates long bolts or studs
Precision machined socket end
Cushion grip handle for comfort
Size imprinted on color coded ends for easy identification
Qty:
Part #:810303
- 1/2 X 3" Nutdriver Cushion GRIP
Hollow shaft accommodates long bolts or studs
Precision machined socket end
Cushion grip handle for comfort
Size imprinted on color coded ends for easy identification
Qty:
Qty:
Part #:810307
- 9" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:810255
- 7" Cape Chisels
Designed for cutting or grooving keyholes or slots
Qty:
Displaying: 1 - 24 of 30 Matching Items