3-5/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 3-5/8in 7in
Qty:
Qty:
Qty:
Part #:811713
- 7" Needle Nose Pliers
Polished heads resist rust and corrosion, extending the tool life
Serrated jaws provide extra gripping power
The PL-114CS short nose model is supplied with a spring and is designed for close, fine electrical and mechanical work
The PL-116C long nose model provides excellent gripping ability for use in tight, narrow places
Qty:
Qty:
Qty:
Part #:501440
- 7" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:501137
- 7" Industrial Grade Linesman's Pliers
&bull Designed for wiring, electrical equipment installation and maintenance for utility linemen
&bull Polished faces look good and resist corrosion
&bull Induction-hardened cutting edges stay sharp longer
&bull Diamond serrated jaws provide solid grip on wire
&bull Double-dipped plastic handle grips are comfortable yet durable
Qty:
Part #:812965
- 7" Industrial Grade Diagonal Cutting Pliers
&bull Handles are designed to cut wire with ease
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Induction-hardened cutting edges
&bull Regular flush cutters are used for cutting hard wire
Qty:
Part #:509571
- 1/2" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:306162
- &bull 1000V Rated for safety&bull Durable, two-layer, molded insulation to meet or exceed all ASTM and IEC standards for insulated tools&bull Custom US-made tool steel&bull Cushion-Grip handle for superior torque and comfort&bull Made in the USA&bull This item replaces the 601-6-INS and 601-8-INS
Qty:
Part #:504375
- 1" Drive 6-Point SAE 1-5/8" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:811885
- 3/4" Drive 7" Impact Extension
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Pin and o-ring or RET RING® (sold separately) secure tools onto impact wrench for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Drive end features pin retention hole and groove
Qty:
Qty:
Part #:810255
- 7" Cape Chisels
Designed for cutting or grooving keyholes or slots
Qty:
Part #:810257
- 3/8" Diamond Point Chisels
Designed for making a V-groove in metal and to clean out inside corners
Qty:
Part #:810261
- 7" Round Nose Chisels
Designed for cutting or grooving keyholes or slots
Qty:
Displaying: 1 - 24 of 33 Matching Items