6-3/4in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 6-3/4in 7in
Qty:
Qty:
Part #:811713
- 7" Needle Nose Pliers
Polished heads resist rust and corrosion, extending the tool life
Serrated jaws provide extra gripping power
The PL-114CS short nose model is supplied with a spring and is designed for close, fine electrical and mechanical work
The PL-116C long nose model provides excellent gripping ability for use in tight, narrow places
Qty:
Qty:
Qty:
Qty:
Part #:501440
- 7" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:513127
- 10 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:501137
- 7" Industrial Grade Linesman's Pliers
&bull Designed for wiring, electrical equipment installation and maintenance for utility linemen
&bull Polished faces look good and resist corrosion
&bull Induction-hardened cutting edges stay sharp longer
&bull Diamond serrated jaws provide solid grip on wire
&bull Double-dipped plastic handle grips are comfortable yet durable
Qty:
Part #:812965
- 7" Industrial Grade Diagonal Cutting Pliers
&bull Handles are designed to cut wire with ease
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Induction-hardened cutting edges
&bull Regular flush cutters are used for cutting hard wire
Qty:
Part #:503706
- 1" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:306162
- &bull 1000V Rated for safety&bull Durable, two-layer, molded insulation to meet or exceed all ASTM and IEC standards for insulated tools&bull Custom US-made tool steel&bull Cushion-Grip handle for superior torque and comfort&bull Made in the USA&bull This item replaces the 601-6-INS and 601-8-INS
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:811885
- 3/4" Drive 7" Impact Extension
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Pin and o-ring or RET RING® (sold separately) secure tools onto impact wrench for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Drive end features pin retention hole and groove
Qty:
Qty:
Qty:
Qty:
Displaying: 1 - 24 of 36 Matching Items