7/16in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 7/16in 9in XL
Qty:
Qty:
Part #:504406
- Lineman's Pliers, New England Nose, 9-Inch
&bull High-leverage design. Rivet is closer to the cutting edge for 46-percent greater cutting and gripping power than other plier designs&bull Hot-riveted joint ensures smooth action and no handle wobble&bull Induction hardened cutting knives for long life&bull Streamlined design with sure-gripping, cross-hatched knurled jaws&bull Unique handle tempering helps absorb the ''snap'' when cutting wire&bull Precision-hardened plier head for on-the-job toughness&bull Plastic-dipped handles for comfort and ease of identification&bull ''Handform'' handles for full gripping and cutting power
Qty:
Part #:511845
-
7/16" Wire Rope Clip, Forged Carbon Steel, Galvanized
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Qty:
Qty:
Part #:507925
- 1/4" Drive 6-Point SAE 7/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Part #:501590
- 1/2" Drive SAE 5/8" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503701
- Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:811645
- 1/2" Drive 6-Point SAE 7/16" Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
closeout
$362.00 MSRP
$
263.08
Part #:503781
- CLOSEOUTS Only 1 Left!
- 2.25 max HP, 7"/9" Sander
This 13 amp, 5,500 RPM, 2.25 maximum horsepower sander provides high performance and durability for moderately heavy jobs. Sold without accessories, a 7 or 9 inch backing pad and disc can be attached allowing this tool to be used for removing paint or rust from metal, plastic and fiberglass surfaces. Spiral bevel gears transfer maximum torque for heavy duty jobs. Spring loaded recessed spindle lock assists in easy accessory changes. This tool can be converted to a grinder by purchasing either a 7 inch or 9 inch guard and wheel which are easily attached to the tool. Grinding applications remove more material and may be used to shape metal.
Qty:
Part #:511894
-
7/16" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Qty:
Part #:503872
- General-Purpose Belt, X-Large
&bull Made of strong, heavy-duty leather&bull Removable single-tongue buckle held is by two heavy-duty snaps&bull Belt is 1-1/2-Inch (38 mm) wide&bull Waist size 38- to 46-Inch
Qty:
Part #:507527
- Electricians Leather Tool Belt, X-Large
&bull Made of strong, heavy-duty leather&bull Includes tool loops and chain-tape thong&bull Extra Large Fits sizes 46-Inches to 54-Inches (1168 mm to 1372 mm)&bull Belt is 1-1/2-Inches (38 mm) wide
Qty:
Part #:507877
- Lineman's Square Nose Pliers, 9-Inch
&bull High-leverage design. Rivet is closer to the cutting edge for 46-percent greater cutting and gripping power than other plier designs&bull Hot-riveted joint ensures smooth action and no handle wobble&bull Induction hardened cutting knives for long life&bull Streamlined design with sure-gripping, cross-hatched knurled jaws&bull Unique handle tempering helps absorb the ''snap'' when cutting wire&bull Precision-hardened plier head for on-the-job toughness&bull Plastic-dipped handles for comfort and ease of identification&bull ''Handform'' handles for full gripping and cutting power&bull Custom, US-made tool steel
Qty:
Part #:806750
- High-Leverage Side-Cutters
&bull High-leverage design. Rivet is closer to the cutting edge for 46-percent greater cutting and gripping power than other plier designs&bull High-leverage design. Rivet is closer to the cutting edge for 46-percent greater cutting and gripping power than other plier designs&bull Induction hardened cutting knives for long life&bull Streamlined design with sure-gripping, cross-hatched knurled jaws&bull Unique handle tempering helps absorb the ''snap'' when cutting wire&bull Precision-hardened plier head for on-the-job toughness&bull ''Handform'' handles for full gripping and cutting power&bull Custom, US-made tool steel
Qty:
Part #:501614
- Heavy Duty Lineman's Pliers, 9-Inch
&bull High-leverage design. Rivet is closer to the cutting edge for 46-percent greater cutting and gripping power than other plier designs&bull Heavy-duty, thicker dipped handles are more comfortable and easier to grab with gloved hands&bull Hot-riveted joint ensures smooth action and no handle wobble&bull Induction hardened cutting knives for long life&bull Streamlined design with sure-gripping, cross-hatched knurled jaws&bull Precision-hardened plier head for on-the-job toughness&bull Unique handle tempering helps absorb the ''snap'' when cutting wire&bull ''Handform'' handles for full gripping and cutting power&bull Custom, US-made tool steel
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Displaying: 1 - 24 of 55 Matching Items