Beveling Tool
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Power Tools: Beveling Tool Hoist NiCd Battery Press Tool
closeout
$126.00 MSRP
$
90.00
Part #:505751
- CLOSEOUTS Only 1 Left!
- 14.4V Battery
Choose the best power source for all of your 14.4-Volt Milwaukee cordless tools. With 2.4 amp-hour capacity, the 14.4-volt battery provides power for longer runtimes, so you have less interruption on the job. There&rsquos no memory effect, so the full NiCd battery capacity is always available. The reversible battery pack lets you work in tight spaces, and adjust the balance of the tools for greater comfort and productivity. Use this battery for longlasting, dependable performance with all of your Milwaukee 14.4-volt cordless tools.
Qty:
closeout
$
69.00
Qty:
Part #:834-601751750
- KFM 9-3 RF (601751750) Metal Bevelling Tool metaBOX 215
Compact metal beveling tool for 45° chamfers and radii of 2 to 3 mm at visible edges
Surfaces free from oxide and burrs as ideal preparation for the application of powder or paint coatings for maximum protection from corrosion
One-touch controller Patented, tool-free setting of the cutting depth in 0.1" steps stop points for short setting times, and protection against unintentional adjustment of the cutting depth when working
Slim cutter head with standard carbide indexable inserts and ball-bearing stationary seal ring for working in tubes and in curves
Guide stop for uniform finish and high surface quality when finishing straight edges
Bail handle adjusts without tools for secure, even guiding
Metabo Long-life motor with patented dust protection for long service life
Vario-Constamatic (VC)-Full wave electronics with thumbwheel for working with materials requiring customized speeds, which remain almost constant under load
Electronic safety shutdown of the motor for safe working in case the tool stops unexpectedly
Electronic overload protection, soft start and restart protection
Slim housing for ideal handling
With metaBOX, the smart solution for transportation and storage
Qty:
Part #:729-9565
- 1 Ton Electric Chain Hoist
All Milwaukee Professional Electric Chain Hoists offer an array of load lift and height options. With 1/2 to 2 Ton capacities and 10 ft. to 20 ft. lifting heights, you can order a Milwaukee Electric Chain Hoist to meet your roughest needs. All offer a multi-disc magnetic brake for positive load holding and spotting. Adjustable upper and lower limit switches, overload limiting clutch and latch-type ridged top hook. You can get single or three-phase voltage motors to meet your operation power requirements. The 24-volt pushbutton station fits easily in your hand to allow thumb, trigger or two-handed operation.
Qty:
Part #:729-2473-20
- M12&trade FORCE LOGIC&trade Press Tool
Our M12&trade FORCE LOGIC&trade Press Tool Kit is the lightest press tool on the market and represents a new level in portability and accessibility around installed pipe. The M12&trade press tool features a one-handed, in-line design enabling you to operate the tool nearly anywhere you can fit your arm. Built-in REDLINK&trade technology enables the plumbing press tool to monitor the force output, delivering you with quality connections. A visual indicator alerts you when a secure connection has been achieved and when the tool needs calibration. The cordless press tool features the best calibration standards, only requiring service every 32,000 crimps. This allows you to perform up to 4X more connections between services, keeping the tool on the job site up to 4X longer than competitive units. When used with our MILWAUKEE® press jaws, this tool delivers quality press connections on all major fitting brands. Our FORCE LOGIC&trade press tool is powered by Milwaukee M12&trade REDLITHIUM&trade batteries, allowing you to Cut, Fasten and Connect on One System.
Qty:
Part #:729-2473-22
- M12&trade FORCE LOGIC&trade Press Tool Kit with Jaws
Our M12&trade FORCE LOGIC&trade Press Tool Kit with Jaws is the lightest press tool on the market and represents a new level in portability and accessibility around installed pipe. The M12&trade press tool features a one-handed, in-line design enabling you to operate the tool nearly anywhere you can fit your arm. Built-in REDLINK&trade technology enables the plumbing press tool to monitor the force output, delivering you with quality connections. A visual indicator alerts you when a secure connection has been achieved and when the tool needs calibration. The cordless press tool features the best calibration standards, only requiring service every 32,000 crimps. This allows you to perform up to 4X more connections between services, keeping the tool on the job site up to 4X longer than competitive units. When used with our MILWAUKEE® press jaws, this tool delivers quality press connections on all major fitting brands. Our FORCE LOGIC&trade press tool is powered by Milwaukee M12&trade REDLITHIUM&trade batteries, allowing you to Cut, Fasten and Connect on One System.
Qty:
Part #:729-2773-20L
- Country of Origin DEU:
Qty:
Displaying: 1 - 7 of 7 Matching Items