J.H. Williams
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Brand: J.H. Williams Klein Porter Cable Snap-on Industrial Brands
Part #:504450
- 15 pc 1/4" Drive -Point SAE Shallow Socket and Drive Tool Set Packed Keep Safe Foam in Metal Tool Box
Keep-Safe-Foam system keeps tools organized and helps prevent loss
All tools are professional quality, made of high-grade chrome vanadium steel
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Metal tool box made for years of rugged use
Qty:
Part #:500695
- 1/2" Drive SAE 1/2" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810245
- 6" Cold Chisels 1/2"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503700
- 3/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503704
- 3/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:501976
- Product Details
Chrome plating provides increased protection from rust and corrosion
Drive handles provide extra leverage with greater strength than ratchets
Square drive slides on T-Handles for versatility
Flex handle flex drive swivels 11° in either direction
Spring and plunger socket retention
Qty:
Qty:
Part #:507233
- 7 Pc SAE Nutdriver Set
Hollow shaft accommodates long bolts or studs
Precision machined socket end
Cushion grip handle for comfort
Size imprinted on color coded ends for easy identification
Qty:
Part #:508191
- 29 pc 1/2" Drive 12-Point Metric Shallow Socket and Drive Tool Set Packed Keep Safe Foam in Metal Tool Box
Keep-Safe-Foam system keeps tools organized and helps prevent loss
All tools are professional quality, made of high-grade chrome vanadium steel
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Metal tool box made for years of rugged use
Qty:
Part #:503696
- 1/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:503702
- 1/2" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:506130
- 1/2" Drive Ratcheting Repair Kit For JHWS-52A& JHWS-53
&bull Double pawl design with 72 teeth action provides a 5° ratcheting angle
&bull Shift lever reverses action instantly
&bull Knurled handle provides a non-slip grip
&bull Chrome finish models provides increased protection from rust and corrosion
Qty:
Part #:504197
- 3/4" Drive Universal Joint 3-1/2"
Specially heat treated for impact use to provide long life, safety, and durability
Pin and o-ring or RET RING (sold separately) secure tools onto impact wrench for safety and convenience
Suitable for use with pneumatic and electric impact wrenches
Drive end features pin retention hole and groove
Qty:
Part #:503577
- 18" Heavy Duty Roll Bars
Aligning and prybar with long tapered body and 90 rolling head
Qty:
Part #:502580
- 1" Drive Adapter 1" Female x 3/4" Male 3"
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Pin and o-ring or RET RING® (sold separately) secure tools onto impact wrench for safety and convenience
&bull Universal joint provides 55° range of motion
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Drive end features pin retention hole and groove
Qty:
Part #:1184-JHW50668
- 23 pc 1/2" Drive -Point SAE Shallow and Deep Socket and Drive Tool Set Compact Case
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Packed in rugged compact high-density polyethylene (HDPE) cases that are strong and durable yet light in weight
Qty:
Part #:503692
- 3/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503881
-
Overview
&bull Set-up wedges are used for setting-up work on planers, shapers, milling machines and other similar applications
Qty:
Part #:306243
- Insulated 1/8-Inch Slotted Screwdriver, 4-Inch
Perfect for working in control boxes or other terminal block applications where insulated tools are necessary
1000V Rated for safety
Meets or exceeds IEC 60900 2012, ASTM F1505-10
Durable, two-layer, molded insulation to meet or exceed all ASTM and IEC standards for insulated tools
Made in USA with custom US-made tool steel
Cushion-Grip&trade handle for superior torque and comfort
Made in the USA
Protect yourself when working near an energized source. Clearly marked with the official 1000-volt rating symbol, Klein insulated tools exceed IEC 60900 and ASTM F1505 standards for insulated tools. Two layers of insulation provide protection against electric shock. Perfect for working in control boxes or other terminal block applications where insulated tools are necessary.
Qty:
Part #:801370
- Slotted Screw Holding Screwdriver 6-Inch
&bull Start and drive 1/4-Inch slotted screws with one hand&bull Split-blade screw-holding driver wedges into screw slot&bull Positive gripping action holds, starts, and drives slotted screws in awkward, hard-to-reach places&bull Not designed for torquing or tightening&bull Blade thickness of .043-Inch (1 mm) expanding to .085-Inch (2 mm)
Qty:
Part #:500330
- Multi-Bit Screwdriver / Nut Driver, 5-in-1, Phillips, Slotted Bits
Multi-bit Screwdriver / Nut Driver with Cushion-Grip&trade handle for greater torque and comfort
End of handle is marked to quickly identify tool
Features 5/16-Inch (8 mm) nut driver plus #1 and #2 Phillips, 1/4-Inch and 3/16-Inch (7 mm and 5 mm) slotted screwdrivers
The following replacement bits are available
#1 Phillips and 3/16-Inch [5 mm] Slotted (Cat. No. 32478)
#2 Phillips and 9/32-Inch [7 mm] Slotted (Cat. No. 32479)
Qty:
Displaying: 25 - 48 of 697 Matching Items