J. H. Williams
Hilti
View:
Active Filters :
Part #:511262
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + black cartr #3498241
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
292.49
Qty:
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Part #:511332
-
HIT-RE 500 V3 Epoxy anchor Epoxy adh RE 500-V3 11.1oz/330ml #2123401 Base materialsConcrete (cracked), Concrete (uncracked)Base material conditionDry, Submerged, Water-filled, WetApprovals / Test reportsICC-ES report (concrete)Seismic loadingYesPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 158 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct informationThis product is subject to the Chemicals Prohibition Ordinance (ChemVerbotsV). It is to be used by professionals within the scope of their work and, in accordance with § 8 para. 3 no. 1 of the ChemVerbotsV, is to be used exclusively for its intended purpose as anchor adhesive, for rebar connections (typically steel-to-concrete and/or concrete-to-concrete connections), as well as for other intended fastening and uses within the scope of construction activities. Purchasers must comply with all existing legal requirements for the use of these products and may use them only as permitted. Information in the safety data sheets and operating instructions on the use of these products, the hazards associated with their use, the necessary safety measures during intended use and in the event of unforeseen spillage or release, and proper disposal must always be observed. The operating instructions and safety data sheets can be accessed in the detailed view of the products concerned at www.hilti.de in a format that can be saved and printed, and the operating instructions are enclosed with the products. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. Do not get in eyes, on skin or on clothing. In case of contact with eyes rinse thoroughly with water for several minutes. Remove contact lenses if possible, continue rinsing. If eye irritation, skin irritation or rash persist seek medical advice/attention. In case of contact with skin wash with plenty of soap and water. Disposal Completely emptied cartridges can be disposed of via the Dual System (yellow garbage can). Full/partially emptied containers are to be disposed of as special waste.Product ClassUltimate
$
81.77
Qty:
Part #:511731
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + red cartr #3498242
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
292.49
Qty:
$
44.92
Qty:
Part #:511740
-
Cartridge holder red HIT-CR 500 #2007059
$
45.81
Qty:
Part #:503892
-
Overview
&bull All tools are professional quality, made of high-grade chrome vanadium steel
Qty:
Part #:511684
- 1/2" Drive Crowfoot Wrench Set, Open End, SAE, 12 Pieces
10840 12 Piece 1/2" Drive Crowfoot Wrenches on Clip RailsContents IncludeProduct Code Size (Inches) 10810 15&frasl16 10811 1 10812 1 1&frasl16 10813 1 1&frasl8
10814 1 3&frasl16
10815 1 1&frasl4
10816 1 5&frasl16
10817 1 3&frasl8
10818 1 7&frasl16
10819 1 1&frasl2
10820 1 9&frasl16
10821 1 5&frasl8
Qty:
Part #:508171
- 1" Drive 12-Point SAE 1-3/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:511331
-
HIT-HY 200-A V3 Adhesive anchor (New Verision)
Ultimate-performance injectable hybrid mortar with approvals for anchoring structural steel baseplate and post-installed rebar connections
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS SoftwareYes
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, SeismicPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
HIT-HY 200-A Adhesive anchor Hybrid adh HY 200-A 11.1oz/330ml #2022791 (Old Verision)Base materialsConcrete (cracked), Concrete (uncracked), Masonry (grout-filled CMU)Base material conditionDry, WetApprovals / Test reportsICC-ES report (concrete), SeismicSeismic loadingYesFatigue loadingNoFire resistanceNoPROFIS SoftwareYesClean-TecNoAnchoring elementsHAS threaded rods, HIS-N internally threaded sleeves, HIT-Z torque controlled bonded anchors, RebarCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
$
64.39
Qty:
Part #:511683
-
HIT-HY 200-R Adhesive anchor Hybrid adh HY 200-R 11.1oz/330ml #2022793 Replaced By
HIT-HY 200-R V3 Adhesive anchor
Ultimate-performance injectable hybrid mortar with approvals for post-installed rebar connections and anchoring structural steel baseplate
Base materials Concrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reports DOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS Software Yes
$
64.39
Qty:
Part #:503700
- 3/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503704
- 3/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:501976
- Product Details
Chrome plating provides increased protection from rust and corrosion
Drive handles provide extra leverage with greater strength than ratchets
Square drive slides on T-Handles for versatility
Flex handle flex drive swivels 11° in either direction
Spring and plunger socket retention
Qty:
Part #:500192
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
7.49
Qty:
Part #:508597
-
TE-CX (SDS Plus) Imperial hammer drill bit Hammer drill bit TE-CX 5/8" x 12" #435019
Connection endTE-C (SDS Plus)Base materialReinforced concrete, Concrete, Brick, MasonryWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter5/8 inLength12 inWorking length10 inProduct ClassUltimate
$
92.32
Qty:
Part #:507233
- 7 Pc SAE Nutdriver Set
Hollow shaft accommodates long bolts or studs
Precision machined socket end
Cushion grip handle for comfort
Size imprinted on color coded ends for easy identification
Qty:
Part #:507221
-
HVU2 Anchor capsule Adhesive capsule HVU2 1/2" x 4 1/4" #2234721
Ultimate-performance foil capsule for heavy-duty anchoring in concrete
PROFIS SoftwareYes
Tested/approved for diamond drillingYes
In-service temperature &ndash range-40 - 248 °F
PROFIS SoftwareYesTested/approved for diamond drillingYesIn-service temperature &ndash range-40 - 248 °FStorage and transportation temperature range-4 - 77 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)24 monthsProduct ClassUltimate
Part #:508616
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
2.53
Qty:
Part #:805310
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
3.36
Qty:
Part #:508621
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
4.72
Qty:
Part #:508600
-
TE-CX (SDS Plus) Imperial hammer drill bitHammer drill bit TE-CX 3/4"-12" #2206742
Connection endTE-C (SDS Plus)Base materialReinforced concrete, Concrete, Brick, MasonryWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter3/4 inLength12 inWorking length10 inProduct ClassUltimate
$
83.81
Qty:
Part #:502580
- 1" Drive Adapter 1" Female x 3/4" Male 3"
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Pin and o-ring or RET RING® (sold separately) secure tools onto impact wrench for safety and convenience
&bull Universal joint provides 55° range of motion
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Drive end features pin retention hole and groove
Qty:
Part #:810356
- 1" Drive 12-Point SAE 1-1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Displaying: 1 - 24 of 758 Matching Items