J.H. Williams
Hilti
View:
Active Filters :
- Brand: Hilti J.H. Williams Parker
- Size: 5-1/2lb 5/8in
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Part #:508597
-
TE-CX (SDS Plus) Imperial hammer drill bit Hammer drill bit TE-CX 5/8" x 12" #435019
Connection endTE-C (SDS Plus)Base materialReinforced concrete, Concrete, Brick, MasonryWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter5/8 inLength12 inWorking length10 inProduct ClassUltimate
$
92.32
Qty:
Part #:508621
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
4.72
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:501956
- 6 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:500704
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
6.71
Qty:
Part #:509570
- 5/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Part #:508626
-
HDI+ / HDI Flush anchor Drop-in anchor HDI 5/8" #336428Approvals / Test reportsFM (Factory Mutual), UL (Underwriter Laboratories)Material, corrosionCarbon steel, zinc-platedBase materialsConcrete (lightweight), Concrete (lightweight over metal deck), Concrete (uncracked)PROFIS SoftwareNoDrill bit diameter27/32 inProduct ClassPremium
Qty:
$
2.14
FT
Qty:
Part #:508596
-
TE-CX (SDS Plus) Imperial hammer drill bit Hammer drill bit TE-CX 5/8"-6" #2153828
Connection endTE-C (SDS Plus)Base materialReinforced concrete, Concrete, Brick, MasonryWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter5/8 inLength6 inWorking length4 inProduct ClassUltimate
$
71.87
Qty:
Part #:508634
-
Hand setting tool HST 5/8" #32981 HSD/HST 16-5/8 Setting tool
Manual setting tool for drop-in anchors (HDI-L/HDI/HDI-S/HDV)
$
14.98
Qty:
closeout
Part #:508620
- CLOSEOUTS Only 20 Left!
- Applications; Fastening structural steel, hand rails, signs, racks, equipment and formwork bracing:
$
2.94
Qty:
Part #:810263
- 12" Extra-Long Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:500443
- 3/8" Drive 12-Point SAE 5/8" Shallow Socket
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Metal tool box made for years of rugged use
Qty:
Part #:501132
- 5/8" 12-Point SAE SUPERCOMBO® Black Industrial Finish Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:810413
- 5/8" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Displaying: 1 - 24 of 37 Matching Items