Klein
J.H. Williams
Qty:
Part #:508066
- Proto 1/2" Drive Hex Bit Impact Socket 3/8"
Features and Benefits
Proto® Hex Bit Impact Sockets can be used on stubborn fasteners.
Tight tolerances for snug fit on fastener.
Hex bit impact sockets are used wherever powered drive tools are used to install or remove fasteners.
Hex bit impact sockets are designed to withstand the high torque and force associated with impact tools in repetitive application.
Side locking hole.
Qty:
Part #:810217
- 1/2" Drive SAE 3/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503700
- 3/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:508146
- 3/16-Inch Cabinet Tip Screwdriver 4-Inch
&bull Narrow cabinet tip permits blade access where space is limited&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation&bull Meets or exceeds applicable ASME / ANSI specifications
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:810310
- 10" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:503686
- 3/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:500171
- 3/8" Drive Standard Length Hex Bit Sockets, SAE, High-Polioshed Chrome Finish
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Metal tool box made for years of rugged use
Qty:
Qty:
Qty:
Qty:
Part #:810243
- 5 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810313
- 5" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Part #:806772
- 3/8-Inch Keystone Tip Screwdriver Square
&bull Heavy-duty square shank for wrench-assisted turning&bull Bolster reinforces shank for hard use&bull Designed for the most demanding uses&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Meets or exceeds applicable ASME / ANSI specifications&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation
Qty:
Part #:510262
- 3/16-Inch Cabinet Tip Screwdriver 3-Inch
&bull Narrow cabinet tip permits blade access where space is limited&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation&bull Cushion-Grip handle for greater torque and comfort&bull Meets or exceeds applicable ASME / ANSI specifications
Qty:
Part #:506632
- Coated Flathead Screwdriver, 3/16-Inch Cabinet Tip
&bull Plastic coated for circuit protection only. NOT INSULATED&bull Special plastic coating resists cutting, cracking, and chipping&bull Thin coating permits use in confined areas&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Meets or exceeds applicable ASME / ANSI specifications&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation
Qty:
Part #:806780
- Coated 3/8-Inch Cabinet Tip Screwdriver, 8-Inch
&bull Plastic coated for circuit protection only. NOT INSULATED&bull Special plastic coating resists cutting, cracking, and chipping&bull Thin coating permits use in confined areas&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Meets or exceeds applicable ASME / ANSI specifications&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation
Qty:
Part #:506354
- Coated 3/16-Inch Cabinet Tip Screwdriver, 6-Inch
&bull Plastic coated for circuit protection only. NOT INSULATED&bull Special plastic coating resists cutting, cracking, and chipping&bull Thin coating permits use in confined areas&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Meets or exceeds applicable ASME / ANSI specifications&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation
Qty:
Qty:
Displaying: 1 - 24 of 82 Matching Items