J.H. Williams
Appleton


Displaying: 1 - 24 of 91 Matching Items
91 Items
View:
Part #:303954
Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$ 14.54
Qty:
add to cart
Part #:303997
Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$ 8.34
Qty:
add to cart
Part #:307976
Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
$ 35.25
Qty:
add to cart
Part #:810356
1" Drive 12-Point SAE 1-1/2" Shallow Socket &bull SUPERTORQUE&reg lobular openings for greater turning power without deforming the fastener &bull Designed for quick engagement on both 6 and 12 point fasteners
$69.51 MSRP $ 45.36
Qty:
add to cart
Part #:810222
1/2" Drive SAE 5/8" Standard Length Hex Bit Socket &bull High-polished chrome finish socket cleans easily &bull Two piece design allows bits to be replaced easily
$31.06 MSRP $ 20.27
Qty:
add to cart
Part #:500861
6" Set-Up Wedge
$25.35 MSRP $ 16.54
Qty:
add to cart
Part #:503703
5/8" Shank Diameter Eyebolts Shoulder Pattern Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage Each lot is tested and inspected to insure conformance to specifications Available with UNC Class 2A thread only Eyebolt shanks should never be undercut or eyebolt shank diameters reduced Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
$17.14 MSRP $ 11.18
Qty:
add to cart
Part #:300841
Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$ 2.71
Qty:
add to cart
Part #:302661
Appleton and O-Z/Gedney offer ETP 5000S Series steel EMT set screw couplings. They are used to ground and secure EMT raceway sections together.
$ 4.61
Qty:
add to cart
Part #:302665
Appleton and O-Z/Gedney Hang-On hangers are designed secure rigid metal conduit IMC or EMT to threaded rod supports or directly to mounting surfaces.
$ 2.25
Qty:
add to cart
Part #:306983
Appleton and O-Z/Gedney conduit bushings are used with a locknut to terminate rigid metal conduit or IMC conduit to a box or enclosure. They provide a smooth pulling surface for wires.
$ 1.73
Qty:
add to cart
Part #:307353
Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$ 2.05
Qty:
add to cart
Part #:307367
Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$ 1.06
Qty:
add to cart
Part #:308183
O-Z/Gedney offers clamps and straps. They are used to secure oval/round cables or support runs of rigid metal conduit IMC and EMT.
$ 0.91
Qty:
add to cart
Part #:308317
Appleton Form 35 Malleable Iron Conduit Outlet Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
$ 62.14
Qty:
add to cart
Part #:785-0701011
Rubber End Cap 1-1/2" Cast Iron/Plastic
$6.30 MSRP $ 5.88
Qty:
add to cart
Part #:501590
1/2" Drive SAE 5/8" Long Hex Bit Socket &bull High-polished chrome finish socket cleans easily &bull Two piece design allows bits to be replaced easily
$34.94 MSRP $ 22.79
Qty:
add to cart
Part #:501956
6 1/2" Cold Chisels The most commonly used chisels in the chisel line For cutting, shaping and removing metal softer than the cutting edge of the chisel
$17.14 MSRP $ 11.18
Qty:
add to cart
Part #:811830
1/2" Drive Impact 5" Extension &bull Specially heat treated for impact use to provide long life, safety, and durability &bull Spring plunger provides secure socket retention for safety and convenience &bull Suitable for use with pneumatic and electric impact wrenches
$26.72 MSRP $ 17.43
Qty:
add to cart
Part #:509570
5/8" Shank Diameter Eyebolts Plain Pattern Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage Each lot is tested and inspected to insure conformance to specifications Available with UNC Class 2A thread only Plain pattern eyebolts must never be used to lift an angular load Eyebolt shanks should never be undercut or eyebolt shank diameters reduced To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
$17.14 MSRP $ 11.18
Qty:
add to cart
Part #:301040
O-Z/Gedney Form 7 Iron Conduit Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
$ 7.82
Qty:
add to cart
Part #:301077
Appleton FS and FD Cast Hub Device Boxes are CSA Certified. They provide excellent service in areas where boxes are subject to rough usage. FS and FD boxes are used to connect and change direction of conduit runs allow connections for branch runs and serve as pulling fittings and permit access to conductors for splicing and maintenance. They can accommodate wiring devices such as switches and receptacles.
$ 42.11
Qty:
add to cart
$ 42.11
Qty:
add to cart
$ 42.11
Qty:
add to cart
 
Displaying: 1 - 24 of 91 Matching Items