Jamesbury
A.Y. Mcdonald Water Works
View:
Active Filters :
- Brand: A.Y. Mcdonald Water Works Jamesbury Michigan Drill Corp
- Connection: AWWA CTS x FNPT
Part #:203890
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203880
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203886
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203887
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:200255
- Brass Bushings AWWA x AWWA Bushing
A.Y. McDonald brass bushings are designed and used to change the thread of the inlet of a Corporation Stop or tap of a Saddle. Bushingsinclude a generous size wrench flat for ease of installation and lay length for the appropriate thread size.
Qty:
Part #:130-4128-126
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components conform to ASTM B62 and ASTM B584, UNS C83600• Certified to NSF/ANSI 61• Silicon Bronze bolts• EPDM o-ring• Pipe and tap size, and thread type identified on saddle• Outlet boss with large wrench flats:
$
169.11
Qty:
Part #:130-4128-108
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components conform to ASTM B62 and ASTM B584, UNS C83600• Certified to NSF/ANSI 61• Silicon Bronze bolts• EPDM o-ring• Pipe and tap size, and thread type identified on saddle• Outlet boss with large wrench flats:
$
70.13
Qty:
Part #:130-4168-002
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components conform to ASTM B62 and ASTM B584, UNS C83600• Certified to NSF/ANSI 61• Silicon Bronze hinge pin and bolt(s)• EPDM o-ring• Pipe and tap size, and thread type identified on saddle• Outlet boss with large wrench flats:
$
53.05
Qty:
Part #:130-4168-006
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components conform to ASTM B62 and ASTM B584, UNS C83600• Certified to NSF/ANSI 61• Silicon Bronze hinge pin and bolt(s)• EPDM o-ring• Pipe and tap size, and thread type identified on saddle• Outlet boss with large wrench flats:
$
66.42
Qty:
Part #:130-5139-000
- Straight Ball Valves - Compression x FIP 90º ON/OFF TEE OPERATING HEAD, T CTS x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
182.85
Qty:
Displaying: 1 - 10 of 10 Matching Items