Milwaukee Tools
J.H. Williams
View:
Active Filters :
- Brand: J.H. Williams Milwaukee Tools
- Size: 1-1/4in 1-3/18in
Part #:507857
- 3/4" Drive SAE 1-1/4" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:503805
- 1/2" Drive 6-Point SAE 1-1/4" Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Part #:503695
- 1-1/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503256
- Spline Bit 2-Cutter 1-1/4" x 16"
Qty:
Part #:500385
- 1-1/4" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:805207
- 1/2" Drive SAE 1-1/4" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:507836
- 1/2" Drive SAE 1-1/4" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:500467
- 1/2" Drive 12-Point SAE 1-1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:810364
- 3/4" Drive 12-Point SAE 1-1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:501971
- 3/4" Drive 6-Point SAE 1-1/4" Deep Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:503707
- 1-1/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:1184-JHW8908
- 1-1/4" SAE Offset Structural Box Wrench
&bull Offset from handle to permit clearance of obstructions
&bull Handles are tapered for insertion into bolt holes
&bull Industrial Black Finish
Qty:
Part #:1184-JHW16-640
- 3/4" Drive Deep Impact Sockets, 6-Point, SAE
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:729-49-57-1250
- Country of Origin JPN:
Qty:
Part #:729-49-25-1503
- OPEN-LOK&trade 1-3/8" TITANIUM ENHANCED CARBIDE TEETH METAL BLADE 3PK
Our Universal Fit OPEN-LOK&trade Titanium Enhanced Carbide Teeth EXTREME Materials Blades for Oscillating Multi-Tools are designed for use in the most Extreme material cutting applications. For use in wood, screws, nails, cement board, plaster, and other cutting applications, the Titanium Enhanced Carbide Teeth Extreme Materials Blade is complete with a thinner blade and unique aggressive tooth design that offers faster cutting performance in wood when compared to the standard carbide blade. The Extreme Materials Carbide Teeth Blade lasts up to 50X longer than standard bi-metal blades and can be used in a wide range of materials. These Milwaukee multi-tool blades are designed and made in the USA with global materials. This blade is available in 1-3/8&rdquo width in 1, 2, 3 and 5 packs.
Qty:
Displaying: 1 - 15 of 15 Matching Items