Ideal
J.H. Williams
View:
Active Filters :
- Brand: J.H. Williams Ideal Sepco Square D
- Size: 1/2in
Part #:500695
- 1/2" Drive SAE 1/2" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810245
- 6" Cold Chisels 1/2"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:503702
- 1/2" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:801544
- Unlike other PTFE fluorocarbon filament packing, SEPCO prelubricates the fibers of the ML2235 to provide a softer, more flexible packing, with improved peripheral speed characteristics and exothermic properties.
No glazing at higher speed applications, inert, lower coefficient of friction, thermal resistance to 500F/260C and high compressive strength.
Part #:810220
- 1/2" Drive SAE 1/2" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810314
- 6" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Part #:800290
- A 100% pure PTFE joint sealant used in virtually any gasketing applications. Adhesive backing allows for easy installation and material is soft and flexible so it handles curves and contours.
Installation takes only minutes and removal of the sealant is simple and involves no scraping or grinding. It is sold in continuous lengths so that it can be cut off in various lengths.
Part #:801891
- The SEPCO ML2225 are saturated and sealed with the PTFE particles, protecting the fibers from chemical action. A surface coating of PTFE is applied after braiding to assure good break-in characteristics, also a special high temperature lubricant is added. The ML2225 is a great general service on rotary and reciprocating pumps, and agitators. Yarns are coated in PTFE suspensoid.This system of impregnation assures even distribution of the PTFE particles, protecting the fibers from chemical action.
Part #:805047
- ML402 features a blend of synthetic fibers treated with specially formulated lubricants with a saxoline base.
The lubrication formulation makes the extra difference. The ductile nature of the lubricant prevents wicking and provides superior sealability.
The packing is constructed with a Multi-Lok braid and each strand is individually coated with graphite. The packing receives a final secondary surface coating of graphite.
Part #:805053
- The SEPCO ML2225 are saturated and sealed with the PTFE particles, protecting the fibers from chemical action. A surface coating of PTFE is applied after braiding to assure good break-in characteristics, also a special high temperature lubricant is added. The ML2225 is a great general service on rotary and reciprocating pumps, and agitators. Yarns are coated in PTFE suspensoid.This system of impregnation assures even distribution of the PTFE particles, protecting the fibers from chemical action.
Part #:808275
- ML402 features a blend of synthetic fibers treated with specially formulated lubricants with a saxoline base.
The lubrication formulation makes the extra difference. The ductile nature of the lubricant prevents wicking and provides superior sealability.
The packing is constructed with a Multi-Lok braid and each strand is individually coated with graphite. The packing receives a final secondary surface coating of graphite.
Part #:1184-JHWISFXT616
- 3/8" Drive 6-Point SAE 1/2" 6.57"/116.9mm Shank Length Tension Socket Flextension
Made in the U.S.A
Durable black oxide finish
Socket retention pin is TIG welded, providing full rotation power to the socket
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Drive end has a 7/32" cross hole & bevel for ease of use
Up to 30 degree angle offset
Flextensions are designed for use on hand and power tools (Impulse or Direct drive) NOT FOR IMPACT TOOL USE
Maximum working torque values 160 Ft. Lbs. /1920 In. Lbs. /217 Nm
Other lengths and socket sizes available by special order. Contact your Snap-on Industrial Brands representative
Qty:
Part #:811844
- 1/2" Drive SAE 1/2" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:509571
- 1/2" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:811596
- 3/8" Drive 6-Point SAE 1/2" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:811907
- 3/8" Drive 6-Point SAE 1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:302507
- Ductile Iron Bender Head, 1/2" EMT
IDEAL® Iron conduit bender head with handle has ductile iron construction for exceptional durability and rugged construction that withstands a lifetime of heavy use. Baked-on blue enamel finish on the handle resists corrosion and enhances visibility. Bends conduit pipes to fit around any corner, ceiling, wall or irregularly shaped passageways. It features precision marks locating degree scale, star, arrow and rim notch for perfect bends every time. Bender head has easy visibility markings that are raised and cast into both sides. It has a deeply serrated steps and grooved internal hook surface that prevents slippage, while applying high leverage. It is heat treated for extra strength and reinforced at stress points for longer life. Uses the Benfield bending system, which is standard to the industry, resulting in accurate and dependable bends. Includes convenient bending guide as a reference for basic bends. Four sizes provided to accommodates four sizes of pipe. Available complete with head and handle both included, as well as the handle and head each sold separately as a replacement part.
Withstands a lifetime of heavy use
Exceptional, durable, materials for extra strength, and reinforced at stress points for longer life
Ductile iron material is stronger than malleable iron or aluminum
Qty:
Part #:500374
- 1/2" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:500441
- 3/8" Drive 12-Point SAE 1/2" Shallow Socket
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Metal tool box made for years of rugged use
Qty:
Part #:501122
- 1/2" 12-Point SAE SUPERCOMBO® Black Industrial Finish Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:811434
- 1/4" Drive 12-Point SAE 1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:812805
- 1/4" Drive 12-Point SAE 1/2" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for quick engagement on both 6 and 12-point fasteners
Qty:
Part #:812895
- 3/8" Drive 12-Point SAE 1/2" Deep Socket
All tools are professional quality, made of high-grade chrome vanadium steel
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Metal tool box made for years of rugged use
Qty:
Part #:808633
- 1/2" Drive SAE 1/2" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Displaying: 1 - 24 of 31 Matching Items