J.H. Williams
Parker
View:
Active Filters :
- Brand: Parker J.H. Williams Sepco Smith-Blair Inc
- Alt. Size: 3/4"
Qty:
Qty:
Qty:
Qty:
$
6.25
Qty:
Qty:
Qty:
Part #:503704
- 3/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:503692
- 3/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:500377
- 3/4" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:501965
- 14" Extra-Long Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:507842
- 1/2" Drive SAE 3/4" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:507863
- 3/4" Drive SAE 3/4" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:501440
- 7" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:203060
- 245 Redi-Clamp - For repairing punctures, splits, or holes in pipe.
Description A repair clamp designed to repair pin holes, punctures or splits. Application Works on Steel, PVC, HDPE, and Copper tube.
Key Features
Built to a specific pipe O.D.
Drop-in bolts help ease installation
Standard widths are 3", 6", 9" and 12"
Available in IPS, Copper tube, Ductile Iron and other sizes
Lugs are epoxy coated for great corrosion resistance&bullProvides 360º coverage, covering the full pipe surface
18-8 Type 304 Stainless Steel band for corrosion resistance
Economical means of repairing pin hole leaks, punctures and splits in pipe
Qty:
Part #:203091
- 411 Steel Coupling, Straight - For joining plain-end pipe of same outside diameters
Description A bolted sleeve type coupling for joining plain end pipe of the same diameters.Application Joining plain end pipe without the need for welding or special pipe fittings.Key Features
&bullMeets applicable AWWA C219 Standards
&bullAllows for limited expansion and contraction
&bullWill dampen vibration to reduce pipe fatigue
&bullEasy to install, no special pipe end preparation required&bullAvailable in a wide variety of pipe O.D. sizes and sleeve lengths
&bullMost sizes will accommodate anchor studs to restrain the joints
&bullCan be custom made to fit odd O.D.s or other unusual applications
&bullProvided with or without pipe stops to accommodate customer needs
&bullHas good deflection capabilities, allows change in piping direction without the need of elbows, bends
&bullSteel sizes built to specific O.D. and Ductile Iron sizes are built with range to accommodate the variances inDuctile Iron pipe O.D.s
Qty:
Part #:202257
- 525 Compression Coupling - For joining plain-end pipe of same outside diameters or replacing split or excessively damaged pipe
Description A ductile or malleable iron coupling with threaded ends that seal to the pipe when turned.Application Joining plain end pipe of the same diameter.Key Features
&bullStab fit for easier installation
&bullGalvanized finish for additional corrosion resistance
&bullDuctile or malleable iron metal parts for strength and corrosion resistance
&bullMay be used in most water, wastewater and industrial applications&bullWrench flats on the nuts and sleeve help with holding the coupling during tightening
&bullThe retainer cup holds the gasket in place and concentrates gasket compression where it is needed most
&bullThe compression coupling may be used in conjunction with Smith-Blair adapter gaskets to join Copper pipe
&bull Protected gasket extends the life of the gasket and provides electrical continuity between the pipe and the coupling
&bullDeflection of 2º per end allows for pipe movement and installation on pipe that is not perfectly aligned
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:511561
Qty:
Displaying: 1 - 24 of 61 Matching Items