1/2in
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Size: 1/2in 1 Quart 3/4in 12in x 8in
Part #:200084
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -33 PEP-7 x -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204037
- Straight Ball Valves - Compression 90º ON/OFF TEE OPERATING HEAD W/LOCK WING -22 CTS x -22 CTS
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
183.07
Qty:
Qty:
Qty:
Part #:202257
- 525 Compression Coupling - For joining plain-end pipe of same outside diameters or replacing split or excessively damaged pipe
Description A ductile or malleable iron coupling with threaded ends that seal to the pipe when turned.Application Joining plain end pipe of the same diameter.Key Features
&bullStab fit for easier installation
&bullGalvanized finish for additional corrosion resistance
&bullDuctile or malleable iron metal parts for strength and corrosion resistance
&bullMay be used in most water, wastewater and industrial applications&bullWrench flats on the nuts and sleeve help with holding the coupling during tightening
&bullThe retainer cup holds the gasket in place and concentrates gasket compression where it is needed most
&bullThe compression coupling may be used in conjunction with Smith-Blair adapter gaskets to join Copper pipe
&bull Protected gasket extends the life of the gasket and provides electrical continuity between the pipe and the coupling
&bullDeflection of 2º per end allows for pipe movement and installation on pipe that is not perfectly aligned
Qty:
Part #:204264
- BLUE LUBE® Polymer-Based Pipe Gasket Lube
A lubricant for all metal or plastic gasketed pipe including Victaulic type fittings. Works on wet or dry surfaces. Formulated to completely flush from the system and will not transfer taste or odor.
Eliminate Turbidity from the Start with BLUE LUBE®
BLUE LUBE®will flush out of the system without having to repeatedly flush the line, saving both time and water. Does not cause a "greasy" taste in the water like many oleate-based lubricants resulting in fewer customer complaints. NSF approved safe for potable water systems. Will not stain hands or clothes. Cleans up with water or dry towel. Will not become runny at higher temperatures resulting in loss of product. Odorless and cleans up easily.
BLUE LUBE®Pipe Gasket Lube's new formula greatly improves the assembly of mechanical joint couplings and improves pipe slip with both ductile iron and plastic pipe.BLUE LUBE®is an environmentally friendly "green" product that requires less water to flush from the system and prevents turbidity, taste, and/or odor problems in new water main installations.BLUE LUBE® is NSF Standard 61 approved. Patent Pending.
Qty:
Qty:
Part #:205235
-
663 Tapping Sleeve, Stainless Steel, Finger Lug Style, Full Gasket - For tapping size-on-size or reducing branch connections on new or existing pipe
Description All stainless steel tapping sleeve with 360º gasket seal.Application For tapping size-on-size or reducing branch connections on new or existing pipe.Key Features&bull Easy to install&bull Range helps reduce inventory&bull Meets applicable AWWA C223 Standards&bull Molded-in ring in the gasket to ensure effective sealing&bull Nylon washers provided to improve bolt torque capability&bull Heavy gauge, all-Stainless Steel body for rugged performance&bull Fully chemically passivated for maximum corrosion protection&bull ¾" test outlet to allow hydrostatic pressure test before tapping the pipe&bull 360º seal provides maximum support and reinforcement around the pipe in case of pipe break&bull Body drawn out to accept the outlet neck adding to the overall strength of the area under the most stress
$
1,841.06
Qty:
Part #:100367
- Aqua Jet I.D. Controlled PE-4710:
$
0.31
Qty:
Part #:100383
- Aqua Jet I.D. Controlled PE-4710:
$
0.30
Qty:
Qty:
$
7.50
Qty:
Qty:
Part #:203057
- 245 Redi-Clamp - For repairing punctures, splits, or holes in pipe.
Description A repair clamp designed to repair pin holes, punctures or splits. Application Works on Steel, PVC, HDPE, and Copper tube.
Key Features
Built to a specific pipe O.D.
Drop-in bolts help ease installation
Standard widths are 3", 6", 9" and 12"
Available in IPS, Copper tube, Ductile Iron and other sizes
Lugs are epoxy coated for great corrosion resistance&bullProvides 360º coverage, covering the full pipe surface
18-8 Type 304 Stainless Steel band for corrosion resistance
Economical means of repairing pin hole leaks, punctures and splits in pipe
Qty:
Part #:203891
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD Flare x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203900
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204014
- Plug Style - MNPT Inlets MNPT x Flare
A.Y. McDonald Plug Style Corporation Stops come standard with a 360º operating head. The one piece body and plug are precisionmachined to assure a perfect match between the plug and the body to allow operating pressures of 100 PSI on 1/2&rdquo, 3/4&rdquo and 1&rdquo valvesand 80 PSI on 1 1/4&rdquo, 1 1/2&rdquo and 2&rdquo valves. This same machining precision carries over to the threads to assure A.Y. McDonald&rsquos highquality and compatibility with direct taps and saddle applications.
$
81.45
Qty:
Part #:203974
- Plug Style AWWA x Flare
A.Y. McDonald Plug Style Corporation Stops come standard with a 360º operating head. The one piece body and plug are precisionmachined to assure a perfect match between the plug and the body to allow operating pressures of 100 PSI on 1/2&rdquo, 3/4&rdquo and 1&rdquo valvesand 80 PSI on 1 1/4&rdquo, 1 1/2&rdquo and 2&rdquo valves. This same machining precision carries over to the threads to assure A.Y. McDonald&rsquos highquality and compatibility with direct taps and saddle applications.
$
81.45
Qty:
Part #:130-5140-101
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Certified to NSF/ANSI 61 and NSF/ANSI 372• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• Rated for 100 PSIG water pressure• Insert stiffeners required on all flexible plastic connections:
$
106.58
Qty:
Part #:203466
- Straight Adaptors ONE END FEMALE COPPER FLARE -33 PEP-7 x Female Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.The 74755 series fittings are designed to connect any A.Y. McDonald flare end to a different size or end connection.- Note 4755GSKT copper gasket included with all 74755 connections.
Qty:
Part #:204033
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure:
$
142.00
Qty:
Part #:207101
- Meter Couplings - Straight 3/4&rdquo METER SWIVEL FITS 5/8" X 3/4" OR 3/4" METERS Meter Swivel x MNPT Smooth Barrel 2-1/2" Length
Meter swivel nuts are less saddle, have internal straight threads per AWWA C700 and include hole for wire seal unless otherwiseindicated. EPDM rubber gaskets are supplied and are standard.(For Meter Dimensions see page 263)
$
38.70
Qty:
Part #:203166
- SUBMITTAL INFORMATION Manufactured in compliance with ANSI/AWWA C800 (latest revision) Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL” Certified to NSF/ANSI 61 and NSF/ANSI 372 Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision) Large wrench flats provided for proper installation:
Qty:
Part #:130-5123-003
- Meter Couplings -Straight Meter Couplings - Straight 1-5/8" Length, FNPT x Male Meter Thread
Meter swivel nuts are less saddle, have internal straight threads per AWWA C700 and include hole for wire seal unless otherwiseindicated. EPDM rubber gaskets are supplied and are standard.(For Meter Dimensions see page 263)
$
31.33
Qty:
Displaying: 25 - 48 of 61 Matching Items