1in
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Size: 1in 2-1/2in 8in x 8in 10in x 8in
Part #:204390
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD -33 PEP-7 x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204704
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -22 CTS x -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203092
- 411 Steel Coupling, Straight - For joining plain-end pipe of same outside diameters
Description A bolted sleeve type coupling for joining plain end pipe of the same diameters.Application Joining plain end pipe without the need for welding or special pipe fittings.Key Features
&bullMeets applicable AWWA C219 Standards
&bullAllows for limited expansion and contraction
&bullWill dampen vibration to reduce pipe fatigue
&bullEasy to install, no special pipe end preparation required&bullAvailable in a wide variety of pipe O.D. sizes and sleeve lengths
&bullMost sizes will accommodate anchor studs to restrain the joints
&bullCan be custom made to fit odd O.D.s or other unusual applications
&bullProvided with or without pipe stops to accommodate customer needs
&bullHas good deflection capabilities, allows change in piping direction without the need of elbows, bends
&bullSteel sizes built to specific O.D. and Ductile Iron sizes are built with range to accommodate the variances inDuctile Iron pipe O.D.s
Qty:
Part #:200120
- Straight Ball Valves Compression -33 PEP-7 x -33 PEP-7
90º DEGREE ON/OFF TEE OPERATING HEAD
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
343.29
Qty:
Part #:207113
- Straight 1&rdquo METER SWIVEL FITS 1&rdquo METERS, Meter Swivel x MIP L/wire seal hole 2.63in Length
Meter swivel nuts are less saddle, have internal straight threads per AWWA C700 and include hole for wire seal unless otherwiseindicated. EPDM rubber gaskets are supplied and are standard.(For Meter Dimensions see page 263)
$
37.56
Qty:
Part #:204351
- Description SDR35 Gasketed Fittings 10x8 TEE GxGxG
Qty:
Part #:204112
- Description SDR35 Gasketed Fittings 10x8 WYE GxGxG
Qty:
Part #:201741
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -33 PEP-7 x -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204034
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure:
$
233.00
Qty:
Part #:202496
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
Qty:
Part #:204942
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
Qty:
Part #:100665
- Aqua Jet O.D. Controlled PE-4710:
$
0.79
Qty:
Part #:104735
- Aqua Jet O.D. Controlled PE-4710:
$
0.79
Qty:
Part #:202741
- PE-2708 Medium Density Yellow Gas Pipe:
$
0.76
Qty:
Qty:
$
34.45
Qty:
Part #:207452
- Top Height 18in 14lbs Bottom 33in 18lbs
Screw Type Curb Box
$
103.05
Qty:
$
54.45
Qty:
Part #:203927
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD Flare x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203902
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203985
- Plug Style AWWA x Flare
A.Y. McDonald Plug Style Corporation Stops come standard with a 360º operating head. The one piece body and plug are precisionmachined to assure a perfect match between the plug and the body to allow operating pressures of 100 PSI on 1/2&rdquo, 3/4&rdquo and 1&rdquo valvesand 80 PSI on 1 1/4&rdquo, 1 1/2&rdquo and 2&rdquo valves. This same machining precision carries over to the threads to assure A.Y. McDonald&rsquos highquality and compatibility with direct taps and saddle applications.
$
124.48
Qty:
Part #:203475
- Straight Adaptors ONE END FEMALE COPPER FLARE -33 PEP-7 x Female Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.The 74755 series fittings are designed to connect any A.Y. McDonald flare end to a different size or end connection.- Note 4755GSKT copper gasket included with all 74755 connections.
Qty:
Part #:207522
- 411 Steel Coupling, Straight - For joining plain-end pipe of same outside diameters
Description A bolted sleeve type coupling for joining plain end pipe of the same diameters.Application Joining plain end pipe without the need for welding or special pipe fittings.Key Features
&bullMeets applicable AWWA C219 Standards
&bullAllows for limited expansion and contraction
&bullWill dampen vibration to reduce pipe fatigue
&bullEasy to install, no special pipe end preparation required&bullAvailable in a wide variety of pipe O.D. sizes and sleeve lengths
&bullMost sizes will accommodate anchor studs to restrain the joints
&bullCan be custom made to fit odd O.D.s or other unusual applications
&bullProvided with or without pipe stops to accommodate customer needs
&bullHas good deflection capabilities, allows change in piping direction without the need of elbows, bends
&bullSteel sizes built to specific O.D. and Ductile Iron sizes are built with range to accommodate the variances inDuctile Iron pipe O.D.s
Qty:
Part #:200121
- Meter Couplings -Straight Meter Couplings - Straight 1-5/8" Length, FNPT x Male Meter Thread
Meter swivel nuts are less saddle, have internal straight threads per AWWA C700 and include hole for wire seal unless otherwiseindicated. EPDM rubber gaskets are supplied and are standard.(For Meter Dimensions see page 263)
$
35.86
Qty:
Displaying: 25 - 48 of 56 Matching Items