2in x 1in
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Size: 2in x 1in 3/4in x 1in 10in x 8in
Part #:204231
- All Fittings Meet or Exceed
&bull Materials ASTM D-1784, NSF Approved for potable water, NSF 61 &bull Joints ASTM D-3139 &bull Gaskets ASTM F-477 &bull Wall Thickness SDR-21 &bull Pressure Rating 200psi
Qty:
Part #:204567
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204351
- Description SDR35 Gasketed Fittings 10x8 TEE GxGxG
Qty:
Part #:204112
- Description SDR35 Gasketed Fittings 10x8 WYE GxGxG
Qty:
Part #:204942
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
Qty:
Qty:
Part #:204702
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -22 CTS x -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:130-5139-000
- Straight Ball Valves - Compression x FIP 90º ON/OFF TEE OPERATING HEAD, T CTS x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
182.85
Qty:
Part #:130-5125-110
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Displaying: 1 - 9 of 9 Matching Items