1in IPS/1-1/4in CTS
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Size: 1in IPS/1-1/4in CTS 3/4in x 1in 8in x 6in 12in x 8in
Part #:207075
- Description SDR35 Gasketed Fittings 18x6 WYE GxGxG
Qty:
Part #:200262
- SMALL END:
- D3034/F1336 SDR 26 PSM PVC
Qty:
Part #:203297
- Stainless Steel PEP Insert Stiffener ASTM D2239 SIDR 7 and 9
Qty:
Part #:204567
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Qty:
Qty:
Qty:
Part #:204941
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
Qty:
Part #:205235
-
663 Tapping Sleeve, Stainless Steel, Finger Lug Style, Full Gasket - For tapping size-on-size or reducing branch connections on new or existing pipe
Description All stainless steel tapping sleeve with 360º gasket seal.Application For tapping size-on-size or reducing branch connections on new or existing pipe.Key Features&bull Easy to install&bull Range helps reduce inventory&bull Meets applicable AWWA C223 Standards&bull Molded-in ring in the gasket to ensure effective sealing&bull Nylon washers provided to improve bolt torque capability&bull Heavy gauge, all-Stainless Steel body for rugged performance&bull Fully chemically passivated for maximum corrosion protection&bull ¾" test outlet to allow hydrostatic pressure test before tapping the pipe&bull 360º seal provides maximum support and reinforcement around the pipe in case of pipe break&bull Body drawn out to accept the outlet neck adding to the overall strength of the area under the most stress
$
1,841.06
Qty:
Part #:201706
- Description SDR35 Gasketed Fittings 8x6 SADDLE WYE G
Qty:
Qty:
Part #:206997
- Description SDR35 Gasketed Fittings 8x6 TEE GxGxG
Qty:
Part #:204702
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -22 CTS x -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:130-5139-000
- Straight Ball Valves - Compression x FIP 90º ON/OFF TEE OPERATING HEAD, T CTS x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
182.85
Qty:
Displaying: 1 - 14 of 14 Matching Items