3/4in x 1in
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Size: 3/4in x 1in 8in x 6in 12in x 14in
Part #:207075
- Description SDR35 Gasketed Fittings 18x6 WYE GxGxG
Qty:
Part #:200262
- SMALL END:
- D3034/F1336 SDR 26 PSM PVC
Qty:
Part #:204567
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Qty:
Qty:
Part #:204941
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
Qty:
Part #:201706
- Description SDR35 Gasketed Fittings 8x6 SADDLE WYE G
Qty:
Qty:
Part #:206997
- Description SDR35 Gasketed Fittings 8x6 TEE GxGxG
Qty:
Smith Blair Service Saddle Double Bale 12in - 14in x 1in CC 12.62in - 14.32in Range 313-00143209-000
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
Qty:
Part #:204702
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -22 CTS x -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:130-5139-000
- Straight Ball Valves - Compression x FIP 90º ON/OFF TEE OPERATING HEAD, T CTS x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
182.85
Qty:
Displaying: 1 - 12 of 12 Matching Items