1in
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Size: 1in
- General Fitting Type: Ball Curb Valve Coupling MNPT Adapter Service Saddle
Part #:203957
- Straight Adaptors -22 CTS x MNPT ONE END MALE NATIONAL PIPE THREAD
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203945
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204386
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:206974
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
214.16
Qty:
Part #:204390
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD -33 PEP-7 x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203092
- 411 Steel Coupling, Straight - For joining plain-end pipe of same outside diameters
Description A bolted sleeve type coupling for joining plain end pipe of the same diameters.Application Joining plain end pipe without the need for welding or special pipe fittings.Key Features
&bullMeets applicable AWWA C219 Standards
&bullAllows for limited expansion and contraction
&bullWill dampen vibration to reduce pipe fatigue
&bullEasy to install, no special pipe end preparation required&bullAvailable in a wide variety of pipe O.D. sizes and sleeve lengths
&bullMost sizes will accommodate anchor studs to restrain the joints
&bullCan be custom made to fit odd O.D.s or other unusual applications
&bullProvided with or without pipe stops to accommodate customer needs
&bullHas good deflection capabilities, allows change in piping direction without the need of elbows, bends
&bullSteel sizes built to specific O.D. and Ductile Iron sizes are built with range to accommodate the variances inDuctile Iron pipe O.D.s
Qty:
Part #:203927
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD Flare x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203902
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204932
- 525 Compression Coupling - For joining plain-end pipe of same outside diameters or replacing split or excessively damaged pipe
Description A ductile or malleable iron coupling with threaded ends that seal to the pipe when turned.Application Joining plain end pipe of the same diameter.Key Features
&bullStab fit for easier installation
&bullGalvanized finish for additional corrosion resistance
&bullDuctile or malleable iron metal parts for strength and corrosion resistance
&bullMay be used in most water, wastewater and industrial applications&bullWrench flats on the nuts and sleeve help with holding the coupling during tightening
&bullThe retainer cup holds the gasket in place and concentrates gasket compression where it is needed most
&bullThe compression coupling may be used in conjunction with Smith-Blair adapter gaskets to join Copper pipe
&bull Protected gasket extends the life of the gasket and provides electrical continuity between the pipe and the coupling
&bullDeflection of 2º per end allows for pipe movement and installation on pipe that is not perfectly aligned
Qty:
Displaying: 1 - 9 of 9 Matching Items