90 Elbow
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- General Fitting Type: 90 Elbow Bushing Plugs and Clean Outs Valves
Part #:202196
- Description SDR35 Solvent Weld Fittings 6 PSM H x FIPT ADAPTER, Description SDR35 Solvent Weld Fittings 6 RAISED MIPT PLUG
Qty:
Qty:
Part #:202771
- Description SDR35 Solvent Weld Fittings 4 PSM H x FIPT ADAPTER, Description SDR35 Solvent Weld Fittings 4 RAISED MIPT PLUG
Qty:
Part #:203863
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
137.82
Qty:
Part #:130-5122-156
- Elbows - 1/4 Bend. -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:130-5140-103
- Elbows - 1/4 Bend. -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:200120
- Straight Ball Valves Compression -33 PEP-7 x -33 PEP-7
90º DEGREE ON/OFF TEE OPERATING HEAD
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
343.29
Qty:
Qty:
Qty:
Part #:204237
-
All Fittings Meet or Exceed
&bull Materials ASTM D-1784, NSF Approved for potable water, NSF 61 &bull Joints ASTM D-3139 &bull Gaskets ASTM F-477 &bull Wall Thickness SDR-21 &bull Pressure Rating 200psi
Qty:
Qty:
Part #:200255
- Brass Bushings AWWA x AWWA Bushing
A.Y. McDonald brass bushings are designed and used to change the thread of the inlet of a Corporation Stop or tap of a Saddle. Bushingsinclude a generous size wrench flat for ease of installation and lay length for the appropriate thread size.
Qty:
$
749.10
Qty:
$
546.01
Qty:
Part #:130-5139-116
- Straight Ball Valves - Flare x Female National PipeThread (FNPT) Flare x FNPT
90º ON/OFF TEE OPERATING HEAD WITH LOCKWING
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
168.70
Qty:
$
763.20
Qty:
Part #:130-5120-117
- Elbows - 1/4 Bend. ONE END FEMALE COPPER FLARE Swivel Female Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:130-5139-000
- Straight Ball Valves - Compression x FIP 90º ON/OFF TEE OPERATING HEAD, T CTS x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
182.85
Qty:
Part #:130-5131-275
- Stop & Drain Straight Ball Valves - Flare orCompression x FNPT
90º ON/OFF TEE OPERATING HEAD - MINNEAPOLIS PATTERN BODY
A.Y. McDonald Stop & Drain Ball Curb Stops maintain a low turning torque and bubble-tight 150 PSIG water pressure rating due to thePTFE coated brass ball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and threadlocker. McDonald Stop & Drain Ball Curb Stops are available with a wide variety of end connections.All Stop & Drain Ball Valves are Directional and automatically drain from the outlet side when in the closed position
$
318.66
Qty:
$
503.11
Qty:
Qty:
Qty:
Displaying: 1 - 22 of 22 Matching Items