FNPT
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Connection: FNPT Meter XS x Flare
Part #:130-5136-114
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Certified to NSF/ANSI 61 (reference height restrictions)• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Copper tubing made in complianc• Lead free solder joints• Designed to provide proper meter spacing for ease of installation• Padlock wings standard on all valves:
$
250.00
Qty:
Part #:206974
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
214.16
Qty:
Part #:203863
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
137.82
Qty:
Part #:206954
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
438.59
Qty:
Part #:207154
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
530.54
Qty:
Part #:204873
- 331 Repair Service Saddle, Double Bale - For repairing and restoring damaged branch connections
DescriptionDouble bale Ductile Iron repair saddle with large concentric-ribbed gasket and Carbon Steel bales.Application Pulled out or broken direct taps, stripped threads, cracked pipe or new installations wherewide gasket coverage is desired.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullConcentric ribbed gasket conforms to pipe surface irregularities to assure dependable seal&bullNPT, CC and other threaded outlets available in sizes " to 2"
&bullExcellent way to repair and restore a damaged branch connection in one operation
&bullIn conjunction with the bales, a closed lug on one side acts as a hinge for easier installation
Qty:
Part #:204875
- 331 Repair Service Saddle, Double Bale - For repairing and restoring damaged branch connections
DescriptionDouble bale Ductile Iron repair saddle with large concentric-ribbed gasket and Carbon Steel bales.Application Pulled out or broken direct taps, stripped threads, cracked pipe or new installations wherewide gasket coverage is desired.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullConcentric ribbed gasket conforms to pipe surface irregularities to assure dependable seal&bullNPT, CC and other threaded outlets available in sizes " to 2"
&bullExcellent way to repair and restore a damaged branch connection in one operation
&bullIn conjunction with the bales, a closed lug on one side acts as a hinge for easier installation
Qty:
Part #:204854
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
Qty:
$
54.45
Qty:
Part #:203891
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD Flare x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203895
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD Flare x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:200503
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
Qty:
Part #:204851
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
Qty:
Part #:200546
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
Qty:
Part #:204852
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
Qty:
Part #:200431
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Certified to NSF/ANSI 61 and NSF/ANSI 372• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench area provided for proper installation:
$
23.05
Qty:
Part #:130-5123-003
- Meter Couplings -Straight Meter Couplings - Straight 1-5/8" Length, FNPT x Male Meter Thread
Meter swivel nuts are less saddle, have internal straight threads per AWWA C700 and include hole for wire seal unless otherwiseindicated. EPDM rubber gaskets are supplied and are standard.(For Meter Dimensions see page 263)
$
31.33
Qty:
Part #:200432
- Meter Bushings Changes thread size only. Converts 5/8&rdquo meter spud to 5/8&rdquo x 3/4&rdquo meter spud .- one bushing, .50 long
Female Meter x Male Meter
$
8.96
Qty:
Part #:201742
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Certified to NSF/ANSI 61 and NSF/ANSI 372• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation:
Qty:
$
749.10
Qty:
$
546.01
Qty:
Part #:130-5119-139
- Tees. FEMALE OUTLET -22 CTS x -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
$
763.20
Qty:
Part #:130-5120-397
- Tees. FEMALE OUTLET -22 CTS x -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Displaying: 1 - 24 of 25 Matching Items