5/16in-1/4in-20
1-3/8in
View:
Active Filters :
- Size: 1-3/8in 5/16in-1/4in-20 10mm
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:134-J5444H
- Proto® 6 Point Sockets are ideal for use on stubborn or damaged fasteners, and also on fasteners made from soft materials.
The TorquePlus&trade design is a high performance drive configuration which allows for quick and easy socket engagement to the fastener flats, not the corners.
The TorquePlus&trade configuration employs a radius-corner design, shifting contact area and stress away from the fastener corners and distributing contact stresses over a large area of the socket, minimizing slippage.
The TorquePlus&trade internal design minimizes fastener rounding, helps to extend fastener life, and allows the user to more easily turn worn, rounded, or rusted fasteners.
Qty:
Part #:513127
- 10 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:810130
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - 10-24 x M10-1.5
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:729-49-57-1375
- 1-3/8" Threaded Steel Hawg® Cutter
Drill holes up to 3X faster than twist drill bits with the Milwaukee® 3/4-inch Threaded Steel Hawg® Cutter. This long-lasting cutter features carbide teeth and an alternating cutting pattern to cut up to a 2" hole depth in steel, stainless steel, cast iron or aluminum. The spring-loaded, self-ejecting pin lets you make smoother, more accurate cuts and eject the plug faster.The Steel Hawg Cutter works with most electromagnetic drill presses. Use it with arbor 49-57-0030 for Milwaukee's 4262-1 magnetic drill press or arbor 49-57-0010 for Milwaukee's 4292-1 mag press. The 3/4" bit diameter has a metric thread size of M18 x 1.5" shank. Use the Threaded Steel Hawg with a No. 3 Morse Taper Arbor Assembly 49-57-0010.
Qty:
Part #:500387
- 1-3/8" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Qty:
Qty:
Part #:134-J4990-10M
- Made using a heat treated alloy for wear-resistance which helps minimize distortion for a long life.
Hex opening holds the bit allowing the bit holder to take the torque load.
Qty:
Qty:
Qty:
Part #:500402
- 1-3/8" Variable Pitch Hole Saw
Cuts through steel, tin, aluminum, fiberglass, wood and plastic
Deep 1-5/8 In cut to go through wood studs
Extra-tough bi-metal blade made of highest grade tool steel
Steam oxide finish for cooler running saw
Extra-thick backplate minimizes vibration
$
9.20
Qty:
Part #:500495
- 3/4" Drive Shallow Sockets, 12-Point, SAE, High Polished Chrome Finish
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:502076
- 1/2" Drive 12-Point SAE 1-3/8" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Displaying: 1 - 24 of 34 Matching Items