10mm
7/16 in
Part #:511845
-
7/16" Wire Rope Clip, Forged Carbon Steel, Galvanized
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:513127
- 10 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Qty:
Qty:
Qty:
Part #:810130
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - 10-24 x M10-1.5
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:511894
-
7/16" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Qty:
Part #:134-J4990-10M
- Made using a heat treated alloy for wear-resistance which helps minimize distortion for a long life.
Hex opening holds the bit allowing the bit holder to take the torque load.
Qty:
Qty:
Qty:
Qty:
Part #:690-T7645036
-
7/16" Spring Snap Link, Steel, Zinc Plated, #2450
Ideal for Hanging Keys and Other Utility Items From Belt
Fast and Easy to Connect and Disconnect
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Do Not Use to Support Human Weight, for Playground or Athletic Equipment, or as a Safety Device
Qty:
Qty:
Part #:134-JSCVM10T
- COO TW:
Qty:
Displaying: 1 - 15 of 15 Matching Items