Dykem
Adhesives, Sealants, and Tapes
View:
Active Filters :
- Main Category: Adhesives, Sealants, and Tapes
- Brand: Dykem Hilti Loctite
- Anchors: Epoxy
Part #:511332
-
HIT-RE 500 V3 Epoxy anchor Epoxy adh RE 500-V3 11.1oz/330ml #2123401 Base materialsConcrete (cracked), Concrete (uncracked)Base material conditionDry, Submerged, Water-filled, WetApprovals / Test reportsICC-ES report (concrete)Seismic loadingYesPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 158 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct informationThis product is subject to the Chemicals Prohibition Ordinance (ChemVerbotsV). It is to be used by professionals within the scope of their work and, in accordance with § 8 para. 3 no. 1 of the ChemVerbotsV, is to be used exclusively for its intended purpose as anchor adhesive, for rebar connections (typically steel-to-concrete and/or concrete-to-concrete connections), as well as for other intended fastening and uses within the scope of construction activities. Purchasers must comply with all existing legal requirements for the use of these products and may use them only as permitted. Information in the safety data sheets and operating instructions on the use of these products, the hazards associated with their use, the necessary safety measures during intended use and in the event of unforeseen spillage or release, and proper disposal must always be observed. The operating instructions and safety data sheets can be accessed in the detailed view of the products concerned at www.hilti.de in a format that can be saved and printed, and the operating instructions are enclosed with the products. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. Do not get in eyes, on skin or on clothing. In case of contact with eyes rinse thoroughly with water for several minutes. Remove contact lenses if possible, continue rinsing. If eye irritation, skin irritation or rash persist seek medical advice/attention. In case of contact with skin wash with plenty of soap and water. Disposal Completely emptied cartridges can be disposed of via the Dual System (yellow garbage can). Full/partially emptied containers are to be disposed of as special waste.Product ClassUltimate
$
85.86
Qty:
Part #:511331
-
HIT-HY 200-A V3 Adhesive anchor (New Verision)
Ultimate-performance injectable hybrid mortar with approvals for anchoring structural steel baseplate and post-installed rebar connections
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS SoftwareYes
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, SeismicPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
HIT-HY 200-A Adhesive anchor Hybrid adh HY 200-A 11.1oz/330ml #2022791 (Old Verision)Base materialsConcrete (cracked), Concrete (uncracked), Masonry (grout-filled CMU)Base material conditionDry, WetApprovals / Test reportsICC-ES report (concrete), SeismicSeismic loadingYesFatigue loadingNoFire resistanceNoPROFIS SoftwareYesClean-TecNoAnchoring elementsHAS threaded rods, HIS-N internally threaded sleeves, HIT-Z torque controlled bonded anchors, RebarCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
$
67.61
Qty:
Part #:511683
-
HIT-HY 200-R Adhesive anchor Hybrid adh HY 200-R 11.1oz/330ml #2022793 Replaced By HIT-HY 200-R V3
Ultimate-performance injectable hybrid mortar with approvals for post-installed rebar connections and anchoring structural steel baseplate
Base materials Concrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reports DOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS Software Yes
$
67.61
Qty:
Displaying: 1 - 3 of 3 Matching Items