Epoxy
Anchor Rod
View:
Active Filters :
- Anchors: Anchor Rod Epoxy
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Part #:511332
-
HIT-RE 500 V3 Epoxy anchor Epoxy adh RE 500-V3 11.1oz/330ml #2123401 Base materialsConcrete (cracked), Concrete (uncracked)Base material conditionDry, Submerged, Water-filled, WetApprovals / Test reportsICC-ES report (concrete)Seismic loadingYesPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 158 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct informationThis product is subject to the Chemicals Prohibition Ordinance (ChemVerbotsV). It is to be used by professionals within the scope of their work and, in accordance with § 8 para. 3 no. 1 of the ChemVerbotsV, is to be used exclusively for its intended purpose as anchor adhesive, for rebar connections (typically steel-to-concrete and/or concrete-to-concrete connections), as well as for other intended fastening and uses within the scope of construction activities. Purchasers must comply with all existing legal requirements for the use of these products and may use them only as permitted. Information in the safety data sheets and operating instructions on the use of these products, the hazards associated with their use, the necessary safety measures during intended use and in the event of unforeseen spillage or release, and proper disposal must always be observed. The operating instructions and safety data sheets can be accessed in the detailed view of the products concerned at www.hilti.de in a format that can be saved and printed, and the operating instructions are enclosed with the products. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. Do not get in eyes, on skin or on clothing. In case of contact with eyes rinse thoroughly with water for several minutes. Remove contact lenses if possible, continue rinsing. If eye irritation, skin irritation or rash persist seek medical advice/attention. In case of contact with skin wash with plenty of soap and water. Disposal Completely emptied cartridges can be disposed of via the Dual System (yellow garbage can). Full/partially emptied containers are to be disposed of as special waste.Product ClassUltimate
$
81.77
Qty:
Part #:511331
-
HIT-HY 200-A V3 Adhesive anchor (New Verision)
Ultimate-performance injectable hybrid mortar with approvals for anchoring structural steel baseplate and post-installed rebar connections
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS SoftwareYes
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, SeismicPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
HIT-HY 200-A Adhesive anchor Hybrid adh HY 200-A 11.1oz/330ml #2022791 (Old Verision)Base materialsConcrete (cracked), Concrete (uncracked), Masonry (grout-filled CMU)Base material conditionDry, WetApprovals / Test reportsICC-ES report (concrete), SeismicSeismic loadingYesFatigue loadingNoFire resistanceNoPROFIS SoftwareYesClean-TecNoAnchoring elementsHAS threaded rods, HIS-N internally threaded sleeves, HIT-Z torque controlled bonded anchors, RebarCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
$
64.39
Qty:
Part #:511683
-
HIT-HY 200-R Adhesive anchor Hybrid adh HY 200-R 11.1oz/330ml #2022793 Replaced By
HIT-HY 200-R V3 Adhesive anchor
Ultimate-performance injectable hybrid mortar with approvals for post-installed rebar connections and anchoring structural steel baseplate
Base materials Concrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reports DOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS Software Yes
$
64.39
Qty:
Part #:500972
- Anchor rod HAS-E-55 1/2"x6-1/2" #2197991
High-performance anchor rod for adhesive capsules (carbon steel, ASTM F1554 grade 55, zinc-plated)
Material, corrosionCarbon steel, zinc-plated
Wrench/nut size7/8 in
PROFIS SoftwareYes
Material, corrosionCarbon steel, zinc-platedWrench/nut size7/8 inPROFIS SoftwareYesType of fixingPre-fasteningProduct ClassPremium
Part #:521993
-
HAS-E-55 Anchor rod Anchor rod HAS-E-55 1/2"x8" #2197992Material, corrosionCarbon steel, zinc-platedWrench/nut size7/8 inPROFIS SoftwareYesType of fixingPre-fasteningProduct ClassPremium
$
56.06
BAG
Qty:
Part #:500997
- Applications; Suitable for fastenings in concrete and other base materials in combination with the relevant Hilti HIT injectable adhesive mortars. Suitable for fastenings in concrete with Hilti HVU capsules:
Part #:511596
- Anchor rod HAS-E-55 5/8"x9" #2197996
Material, corrosionCarbon steel, zinc-platedWrench/nut size1-1/16 inPROFIS SoftwareYesType of fixingPre-fasteningProduct ClassPremium
Part #:501007
- Anchor rod HAS-E-55 3/4"x10" #2197999
High-performance anchor rod for adhesive capsules (carbon steel, ASTM F1554 grade 55, zinc-plated)
Material, corrosionCarbon steel, zinc-plated
Wrench/nut size1-1/4 in
PROFIS SoftwareYes
Part #:825-2045003
- HAS-R 316 SS Anchor rod
High-performance anchor rod for adhesive capsules and injectable hybrid/epoxy anchors (316 stainless steel)
Material, corrosionStainless Steel, 316
PROFIS SoftwareYes
Cleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Manual Cleaning
$
318.45
BAG
Qty:
Part #:825-2045001
- HAS-R 316 SS Anchor rod
High-performance anchor rod for adhesive capsules and injectable hybrid/epoxy anchors (316 stainless steel)
Material, corrosionStainless Steel, 316
Wrench/nut size9/16 in
PROFIS SoftwareYes
$
185.55
BAG
Qty:
Part #:825-2045002
- HAS-R 316 SS Anchor rod
High-performance anchor rod for adhesive capsules and injectable hybrid/epoxy anchors (316 stainless steel)
Material, corrosionStainless Steel, 316
Wrench/nut size9/16 in
PROFIS SoftwareYes
$
127.55
BAG
Qty:
Part #:825-2045010
- HAS-R 316 SS Anchor rod
High-performance anchor rod for adhesive capsules and injectable hybrid/epoxy anchors (316 stainless steel)
Material, corrosionStainless Steel, 316
PROFIS SoftwareYes
Cleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Manual Cleaning
$
505.95
BAG
Qty:
Part #:825-2197984
- HAS-E Anchor rod
High-performance anchor rod for adhesive capsules (carbon steel, ASTM F1554 grade 55, zinc-plated)
Material, corrosionCarbon steel, zinc-plated
Base materialsConcrete (cracked), Concrete (uncracked), Masonry (hollow), Masonry (solid)
PROFIS SoftwareYes
$
97.15
BAG
Qty:
Part #:825-2197989
- HAS-E Anchor rod
High-performance anchor rod for adhesive capsules (carbon steel, ASTM F1554 grade 55, zinc-plated)
Material, corrosionCarbon steel, zinc-plated
Base materialsConcrete (cracked), Concrete (uncracked), Masonry (hollow), Masonry (solid)
PROFIS SoftwareYes
$
118.75
BAG
Qty:
Part #:825-2197990
- HAS-E Anchor rod
High-performance anchor rod for adhesive capsules (carbon steel, ASTM F1554 grade 55, zinc-plated)
Material, corrosionCarbon steel, zinc-plated
Base materialsConcrete (cracked), Concrete (uncracked), Masonry (hollow), Masonry (solid)
PROFIS SoftwareYes
$
121.75
BAG
Qty:
Part #:500209
-
HAS-E-55 Anchor rod Anchor rod HAS-E-55 7/8"x10" #2198007
High-performance anchor rod for adhesive capsules (carbon steel, ASTM F1554 grade 55, zinc-plated)
Material, corrosionCarbon steel, zinc-plated
Wrench/nut size1-7/16 in
PROFIS SoftwareYes
Material, corrosionCarbon steel, zinc-platedWrench/nut size1-7/16 inPROFIS SoftwareYesType of fixingPre-fasteningProduct ClassPremium
$
187.39
BAG
Qty:
Displaying: 1 - 17 of 17 Matching Items