Fluke
Armstrong International
View:
Active Filters :
Part #:301615
- Key features
DMM test leads (red, black) with safety shrouded, standard diameter banana plugs
Right angle connector on one end and straight connector on the other
Reinforced strain relief
1.5 meter silicone-insulated wire resists heat & cold
CAT IV 600 V, CAT III 1000 V, 10 A rating. CSA listed
One year warranty
$
53.33
Qty:
Part #:304993
- Key features
AC220 SureGrip&trade Alligator Clip Set
TP1 Slim-Reach&trade Test Probes (flat bladed)
TL224 SureGrip&trade Silicone Test Lead Set (straight to right)
One year warranty
$
121.58
Qty:
Part #:306993
- Key features
&ldquoThis meter is perfect for my use as I do HVAC and Electrical work and this will give me what I need for troubleshooting and performance of equipment.&rdquo - Paul
Automatically measure AC and DC voltage up to 600 V with precise digital resolution
Measure current up to 100 A without breaking the circuit with OpenJaw&trade design
Troubleshoot resistance problems up to 1000 &Omega
Work in tight spaces with detachable Slim Reach probe tips
$
196.02
Qty:
Part #:307265
- Key features
Digital multimeter designed specifically for HVAC professionals
Includes built-in thermometer to measure temperature from -40°C to 400°C (-40°F to 752°F)
Provides microamps to test flame sensors
Features low input impedance to helps prevent false readings due to ghost voltage
Presents a large white LED backlight for working in poorly lit areas
Qty:
closeout
$
159.15
Qty:
Part #:310204
- Key features
Ultimate troubleshooting tool for electricians and instrumentation professionals
Combines the functionality of a loop calibrator with the power of a precision 1000 V, 440 mA True-RMS digital multimeter
Optional IR3000FC module for wireless data logging capabilities via Fluke Connect® mobile App
Includes 24 V loop power supply
Features a very large dual display with enhanced two-level backlight brightness settings
Qty:
$
57.70
Qty:
$
0.91
Qty:
$
2.24
Qty:
$
1.31
Qty:
$
1.88
Qty:
$
0.52
Qty:
$
1.56
Qty:
Part #:511262
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + black cartr #3498241
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
292.49
Qty:
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Part #:511332
-
HIT-RE 500 V3 Epoxy anchor Epoxy adh RE 500-V3 11.1oz/330ml #2123401 Base materialsConcrete (cracked), Concrete (uncracked)Base material conditionDry, Submerged, Water-filled, WetApprovals / Test reportsICC-ES report (concrete)Seismic loadingYesPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 158 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct informationThis product is subject to the Chemicals Prohibition Ordinance (ChemVerbotsV). It is to be used by professionals within the scope of their work and, in accordance with § 8 para. 3 no. 1 of the ChemVerbotsV, is to be used exclusively for its intended purpose as anchor adhesive, for rebar connections (typically steel-to-concrete and/or concrete-to-concrete connections), as well as for other intended fastening and uses within the scope of construction activities. Purchasers must comply with all existing legal requirements for the use of these products and may use them only as permitted. Information in the safety data sheets and operating instructions on the use of these products, the hazards associated with their use, the necessary safety measures during intended use and in the event of unforeseen spillage or release, and proper disposal must always be observed. The operating instructions and safety data sheets can be accessed in the detailed view of the products concerned at www.hilti.de in a format that can be saved and printed, and the operating instructions are enclosed with the products. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. Do not get in eyes, on skin or on clothing. In case of contact with eyes rinse thoroughly with water for several minutes. Remove contact lenses if possible, continue rinsing. If eye irritation, skin irritation or rash persist seek medical advice/attention. In case of contact with skin wash with plenty of soap and water. Disposal Completely emptied cartridges can be disposed of via the Dual System (yellow garbage can). Full/partially emptied containers are to be disposed of as special waste.Product ClassUltimate
$
81.77
Qty:
Part #:511731
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + red cartr #3498242
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
292.49
Qty:
$
44.92
Qty:
Part #:511740
-
Cartridge holder red HIT-CR 500 #2007059
$
45.81
Qty:
Part #:511331
-
HIT-HY 200-A V3 Adhesive anchor (New Verision)
Ultimate-performance injectable hybrid mortar with approvals for anchoring structural steel baseplate and post-installed rebar connections
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS SoftwareYes
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, SeismicPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
HIT-HY 200-A Adhesive anchor Hybrid adh HY 200-A 11.1oz/330ml #2022791 (Old Verision)Base materialsConcrete (cracked), Concrete (uncracked), Masonry (grout-filled CMU)Base material conditionDry, WetApprovals / Test reportsICC-ES report (concrete), SeismicSeismic loadingYesFatigue loadingNoFire resistanceNoPROFIS SoftwareYesClean-TecNoAnchoring elementsHAS threaded rods, HIS-N internally threaded sleeves, HIT-Z torque controlled bonded anchors, RebarCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
$
64.39
Qty:
Displaying: 1 - 24 of 2,227 Matching Items