A.Y. Mcdonald Water Works
Avery Products Corp
View:
Active Filters :
Part #:507707
- Area of ApplicationArcal Weld-O is a ready-to-use X-Ray quality welding prep for aluminum and all grades of aluminum alloys. Weld-O is an innovative chemical formulation that consists of a blend of mineral acids, surface active and sequestering agents and degreasers.
Weld-O deoxidizes the surface instantly and conditions the surface for X-ray quality welding. The weld joint is cleaner and stronger. By using Weld-O, the need for wire brushing and other time consuming cleanup procedures are eliminated. A simple water rinse may be done but in many cases is not required.
Qty:
Part #:203957
- Straight Adaptors -22 CTS x MNPT ONE END MALE NATIONAL PIPE THREAD
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203944
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203945
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:130-4771-027
- 5700RING Shut-Off Rod - Centering Ring
$
23.02
Qty:
Part #:203890
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203960
- Straight Adaptors -22 CTS x MNPT ONE END MALE NATIONAL PIPE THREAD
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203964
- Straight Adaptors -22 CTS x MNPT ONE END MALE NATIONAL PIPE THREAD
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204387
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD -33 PEP-7 x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204386
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204022
- Plug Style - AWWA Inlets AWWA x -22 CTS
A.Y. McDonald Plug Style Corporation Stops come standard with a 360º operating head. The one piece body and plug are precisionmachined to assure a perfect match between the plug and the body to allow operating pressures of 100 PSI on 1/2&rdquo, 3/4&rdquo and 1&rdquo valvesand 80 PSI on 1 1/4&rdquo, 1 1/2&rdquo and 2&rdquo valves. This same machining precision carries over to the threads to assure A.Y. McDonald&rsquos highquality and compatibility with direct taps and saddle applications.
$
132.48
Qty:
Part #:204385
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:200055
- Straight Couplings CONNECTIONS FOR DISSIMILAR PIPE OR TUBING -22 CTS x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204403
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -22 CTS x -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204035
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure• Insert stiffeners required on all flexible plastic connections.:
$
154.00
Qty:
Part #:130-5136-114
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Certified to NSF/ANSI 61 (reference height restrictions)• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Copper tubing made in complianc• Lead free solder joints• Designed to provide proper meter spacing for ease of installation• Padlock wings standard on all valves:
$
250.00
Qty:
Part #:501070
-
3-1/2" x 5"
Rectangle
White
Laser
Permanent-Adhesive
50 Sheets
4 Labels per Sheet
200 Total Labels
$
46.60
Qty:
Part #:501073
-
2" x 2"
Rectangle
White
Laser
Permanent-Adhesive
50 Sheets
12 Labels per Sheet
600 Total Labels
$
46.60
Qty:
Part #:508973
Qty:
Part #:804543
- Tap Wrench for No. 0 to 1/4 In. Taps
The #164 Tap Wrench for No. 0 to 1/4 In. Taps is designed to hold and turntaps&mdashtools that cut threads on the inner surface of a hole or pipe&mdashor other small tools, such as hand reamers and screw extractors.
Length 2-7/8 in.
Qty:
Part #:506847
- Product Description
The #377 Welding Magnet with 50 Lb. Pull eliminates the need for clamps or temporary fasteners.
Features
Holds steel plates at any of five angles
Specifications
Magnetic pull force 50 lb.
Holding angles 30°, 45°, 60°, 75°, 90°
- See more at https//www.generaltools.com/welding-magnet-with-50-lb-pull#sthash.iQYGXUbb.dpuf
Qty:
Part #:201394
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD -33 PEP-7 x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:202743
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components conform to ASTM B62 and ASTM B584, UNS C83600• Certified to NSF/ANSI 61• Silicon Bronze bolts• EPDM o-ring• Pipe and tap size, and thread type identified on saddle• Outlet boss with large wrench flats:
$
53.05
Qty:
Displaying: 1 - 24 of 217 Matching Items