J.H. Williams
Baldor
View:
Active Filters :
- Brand: Baldor J.H. Williams
$
1,436.54
Qty:
$
708.42
Qty:
Part #:302335
- .33HP, 1140RPM, 1PH, 60HZ, 56, 3424L, TEFC, F1
$
654.33
Qty:
Part #:302577
- .75HP, 1140RPM, 1PH, 60HZ, 56H, 3528LC, TEFC, F
$
1,072.97
Qty:
$
708.42
Qty:
$
787.22
Qty:
$
832.52
Qty:
$
854.17
Qty:
$
882.41
Qty:
$
951.35
Qty:
$
2,213.24
Qty:
Part #:302911
- 20HP, 1770RPM, 3PH, 60HZ, 256T, 0960M, TEFC, F1
Output20.000 hp
Phase3
Synchronous Speed1,800 rpm
Frequency60.00 Hz
Voltage230 V460 V
Frame MaterialIron
Frame256T
XP Class and GroupNONE
XP DivisionNot Applicable
BrandBaldor-Reliance
Agency ApprovalsCSACSA EEVUR
Ambient Temperature40 °C
Auxillary BoxNo Auxillary Box
Auxillary Box Lead TerminationNone
Base IndicatorRigid
Bearing Grease TypePOLYREX EM (-20F +300F)
BlowerNone
Current52.0 A @ 208 V48.0 A @ 230 V24.0 A @ 460 V
Design CodeA
Drip CoverNo Drip Cover
Duty RatingCONT
Efficiency @ 100% Load93.0%
Electrically Isolated BearingNot Electrically Isolated
Feedback DeviceNo feedback
Front Face CodeStandard
Front Shaft IndicatorNone
Heater IndicatorNo heater
High Voltage Full Load Amps24.0 A
Insulation ClassF
Inverter CodeInverter ready
KVA CodeJ
Lifting LugsStandard Lifting Lugs
Locked Bearing IndicatorLocked Bearing
Motor Lead ExitKO Box
Motor Lead Quantity/Wire Size9 @ 10 AWG
Motor Lead TerminationFlying Leads
Motor StandardsNEMA
Motor Type0960M
Number of Poles4
Overall Length23.28 in
Power Factor83
Product FamilyGeneral Purpose
Pulley End Bearing TypeBall
Pulley Face CodeStandard
Pulley Shaft IndicatorStandard
Rodent ScreenNone
Service Factor1.15
Shaft Diameter1.625 in
Shaft Extension LocationPulley End
Shaft Ground IndicatorNo Shaft Grounding
Shaft RotationReversible
Shaft Slinger IndicatorShaft Slinger
Speed1,770 rpm
Speed CodeSingle Speed
Starting MethodDirect on line
Thermal Device - BearingNONE (OLD)
Thermal Device - WindingNone
Vibration Sensor IndicatorNo Vibration Sensor
Winding Thermal 1None
Winding Thermal 2None
$
2,683.32
Qty:
$
1,594.76
Qty:
$
426.10
Qty:
Part #:503892
-
Overview
&bull All tools are professional quality, made of high-grade chrome vanadium steel
Qty:
Part #:511684
- 1/2" Drive Crowfoot Wrench Set, Open End, SAE, 12 Pieces
10840 12 Piece 1/2" Drive Crowfoot Wrenches on Clip RailsContents IncludeProduct Code Size (Inches) 10810 15&frasl16 10811 1 10812 1 1&frasl16 10813 1 1&frasl8
10814 1 3&frasl16
10815 1 1&frasl4
10816 1 5&frasl16
10817 1 3&frasl8
10818 1 7&frasl16
10819 1 1&frasl2
10820 1 9&frasl16
10821 1 5&frasl8
Qty:
Part #:508171
- 1" Drive 12-Point SAE 1-3/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:503700
- 3/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503704
- 3/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:501976
- Product Details
Chrome plating provides increased protection from rust and corrosion
Drive handles provide extra leverage with greater strength than ratchets
Square drive slides on T-Handles for versatility
Flex handle flex drive swivels 11° in either direction
Spring and plunger socket retention
Qty:
Part #:507233
- 7 Pc SAE Nutdriver Set
Hollow shaft accommodates long bolts or studs
Precision machined socket end
Cushion grip handle for comfort
Size imprinted on color coded ends for easy identification
Qty:
Part #:502580
- 1" Drive Adapter 1" Female x 3/4" Male 3"
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Pin and o-ring or RET RING® (sold separately) secure tools onto impact wrench for safety and convenience
&bull Universal joint provides 55° range of motion
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Drive end features pin retention hole and groove
Qty:
Part #:810356
- 1" Drive 12-Point SAE 1-1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Displaying: 1 - 24 of 656 Matching Items