Gates
Campbell
$
16.30
Qty:
Part #:500327
- ITEM SPECIFICATIONS
Bend Radius
5 IN
Cover Color
Clear
Hose (ID)
1-1/2 IN
Hose (OD)
1.83 IN
Temperature Range
15°F to 140°F
Working Pressure
70 PSI
Item Weight
0.39 lbs per EA
Qty:
$
2.04
Qty:
Qty:
Part #:500566
- #2 Twist Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility Applications
Standard Material Low Carbon Steel
Standard Finish Bright, Zinc Plated and Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Qty:
Part #:502912
-
3/16&rdquo Cold Shut, Steel, Zinc Plated
Connections for Chain and Attachments
When Using Cold Shuts with Chain, Use One Size Larger Than Chain Size
With A Hammer, Drive the Open End Through the Cold Shut Eye. Peen the Extended End to Prevent Opening
Order Unit is "Each"
Note Cold Shuts Should Not Be Reused After Closure Has Been Made
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Qty:
Part #:504474
- Replaces Gates 19B Plantmaster Extreme 3219-2908
$
4.61
Qty:
$
108.64
Qty:
Part #:507505
-
5/16" Alloy Clevis Slip Hook, Forged Alloy, Painted Orange
Material is Heat-Treated Alloy Steel
Alloy Hooks Are Painted Orange and Stamped "AH"
1/4" to 3/8" Hooks Have Drilled Hole for Latch Kit
Design Factor 3.5 to 1
Slip Hooks Are Designed to Allow Chain to Slip Through the Hook
Hooks are Sized by the Material Diameter of the Chain That They Engage. Make Sure the Hook Size and Chain Diameter are Compatible Before Attaching to Load
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:508023
-
3/8" Grade 30 Proof Coil Chain, Zinc Plated, 63' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511262
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + black cartr #3498241
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
307.12
Qty:
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Part #:511332
-
HIT-RE 500 V3 Epoxy anchor Epoxy adh RE 500-V3 11.1oz/330ml #2123401 Base materialsConcrete (cracked), Concrete (uncracked)Base material conditionDry, Submerged, Water-filled, WetApprovals / Test reportsICC-ES report (concrete)Seismic loadingYesPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 158 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct informationThis product is subject to the Chemicals Prohibition Ordinance (ChemVerbotsV). It is to be used by professionals within the scope of their work and, in accordance with § 8 para. 3 no. 1 of the ChemVerbotsV, is to be used exclusively for its intended purpose as anchor adhesive, for rebar connections (typically steel-to-concrete and/or concrete-to-concrete connections), as well as for other intended fastening and uses within the scope of construction activities. Purchasers must comply with all existing legal requirements for the use of these products and may use them only as permitted. Information in the safety data sheets and operating instructions on the use of these products, the hazards associated with their use, the necessary safety measures during intended use and in the event of unforeseen spillage or release, and proper disposal must always be observed. The operating instructions and safety data sheets can be accessed in the detailed view of the products concerned at www.hilti.de in a format that can be saved and printed, and the operating instructions are enclosed with the products. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. Do not get in eyes, on skin or on clothing. In case of contact with eyes rinse thoroughly with water for several minutes. Remove contact lenses if possible, continue rinsing. If eye irritation, skin irritation or rash persist seek medical advice/attention. In case of contact with skin wash with plenty of soap and water. Disposal Completely emptied cartridges can be disposed of via the Dual System (yellow garbage can). Full/partially emptied containers are to be disposed of as special waste.Product ClassUltimate
$
85.86
Qty:
Part #:511731
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + red cartr #3498242
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
307.12
Qty:
$
47.15
Qty:
Part #:511740
-
Cartridge holder red HIT-CR 500 #2007059
$
48.09
Qty:
Part #:511841
- 3/16" Wire Rope Clip, Electro-Galvanized
If Used on Coated Cable, Remove the Coating From the Assembly Area
Follow Assembly Instructions
Qty:
Part #:511866
-
1/2" Clevis Grab Hook, Forged Steel, Self Colored
Forged Steel
Grade 43
UPC Tagged
Grab Hooks Are Designed to Grab a Chain Link and Hold it in Place
Hooks are Sized by the Material Diameter of the Chain That They Engage. Make Sure the Hook Size and Chain Diameter are Compatible Before Attaching to Load
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511892
-
5/16" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Displaying: 1 - 24 of 802 Matching Items