1-gang
Electrical Equipment
View:
Active Filters :
- Main Category: Electrical Equipment
- Size: 1-gang 3/8in
Part #:304966
- Extremely durable for hard-use institutional applications. Spring-loaded covers close automatically when plugs are removed. Die-cast copper-free aluminum construction. Stainless steel springs. Screws and spring covers are chrome-plated brass. Baked-on lacquer finish. Heavy rubber gaskets provide positive seal. All covers below are for 4 screw mounting only. Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
$
12.35
Qty:
Part #:306826
- Appleton and O-Z/Gedney offer NEER connectors for nonmetallic sheathed cable. Type C two screw connectors with locknut and male NPS threaded hub are an open throat type for nonmetallic sheathed cable. Type RX two piece two screw connectors are used to terminate one or more nonmetallic sheathed cables to a knockout in a dry location box or enclosure. Type NST PVC (plastic) connectors are used to terminate nonmetallic sheathed cable to 1/2 knockout in a dry location box or enclosure.
$
0.71
Qty:
Part #:307296
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
10.37
Qty:
Part #:307346
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
0.79
Qty:
Part #:303701
- One Gang Heavy Cast Aluminum Cover Duplex Receptacle Horizontal, Gray
Extremely durable for hard-use institutional applications.
Spring-loaded covers close automatically when plugs are removed.
Die-cast copper-free aluminum construction.
Stainless steel springs.
Screws and spring covers are chrome-plated brass.
Baked-on lacquer finish.
Heavy rubber gaskets provide positive seal.
All covers below are for 4 screw mounting only.
Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
CSA File Number 16807
Qty:
Part #:303205
- WP BOX 1G 3 HOLE 1/2 WPB23
Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
CSA File Number 17695
Qty:
Part #:307182
- Toggle Switch Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:307185
- Duplex Receptacle Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:307154
- Blank Plates, Box Mounted, One Gang, Ivory
Molded of rugged, practically indestructible self-extinguishing nylon. ('TP' series only.)
Available in 'TP' series, extra 3/16 inch width and height than Standard size plates and 'TPJ' series, extra 3/16 inch width and height than Junior-Jumbo size plates.
Available in Ivory, White, Brown, Gray, Black, Blue, Orange, Red, and Light Almond.
Preferred for hospital, industrial, institutional, and other high-abuse applications.
Nominal thickness, .070 inch.
cULus ListingNumber 143222
Qty:
Part #:300310
- Single Gang Cast While-In-Use Cover, Gray
Compliant with National Electric Code (NEC) Section 406.8(B)(1) for wet locations.
UL listed for ''Extra-Duty'' applications.
Heavy cast aluminum construction.
Corner hinge allows for vertical or horizontal mounting.
Device inserts allow for multiple device types.
Install without removing electrical device thanks to keyed mounting holes.
Cord flap gaskets inhibit water splash and insects, all gaskets are factory installed.
Accepts padlocks.
Qty:
Part #:303196
- One Gang Blank Cover, Brushed Aluminum
Designed for both interior and exterior applications.
Universal aluminum mounting plates.
Gray, bronze and white models have baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
CSA File Number 17695
Qty:
Part #:307371
- Weatherproof Single Gang Box, Gray
Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
CSA File Number 17695
Qty:
Part #:300341
- Power Outlet Receptacle Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:302146
- Appleton liquidtight ST Series plain throat and STB Series insulated throat connectors provide a dependable connection for liquidtight flexible metal conduit. Available in straight 45 and 90 styles and trade sizes from 3/8 through 4 . The compact design results in a connector that offers a small turning radius. They seal out oil water dust dirt and fumes.
$
13.30
Qty:
Part #:303227
- Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
Qty:
Part #:306845
- Appleton combination couplings are used to couple flexible metal conduit to EMT conduit. Their armored cable and flexible metal conduit connectors are used to ground and secure armored ground wire armored cable nonmetallic sheathed cable and flexible metal conduit to boxes and enclosures.
$
2.79
Qty:
Part #:306846
- Appleton combination couplings are used to couple flexible metal conduit to EMT conduit. Their armored cable and flexible metal conduit connectors are used to ground and secure armored ground wire armored cable nonmetallic sheathed cable and flexible metal conduit to boxes and enclosures.
$
4.41
Qty:
Part #:306857
- Appleton combination couplings are used to couple flexible metal conduit to EMT conduit. Their armored cable and flexible metal conduit connectors are used to ground and secure armored ground wire armored cable nonmetallic sheathed cable and flexible metal conduit to boxes and enclosures.
$
6.24
Qty:
Part #:306862
- Appleton combination couplings are used to couple flexible metal conduit to EMT conduit. Their armored cable and flexible metal conduit connectors are used to ground and secure armored ground wire armored cable nonmetallic sheathed cable and flexible metal conduit to boxes and enclosures.
$
4.43
Qty:
Part #:306945
- Appleton bus drop cable supports and clamps are designed for exposed branch feeder installations. They support cable in flexible connecting circuits that are used to feed equipment. The cable is run in fixed overhead bused structures to a point directly above equipment then dropped with a 90 bend. At the point of drop the cable clamp is installed to support the cable. Mooring cable clamps are used to attach a guy wire to the cable where it leaves bus structure thus preventing wire terminal strain and possible conductor breakage.
$
0.69
Qty:
Part #:307362
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
0.51
Qty:
Part #:307971
- Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
$
7.37
Qty:
Part #:307983
- Appleton liquidtight ST Series plain throat and STB Series insulated throat connectors and external grounding lugs are for use with liquidtight flexible metal conduit where an external visible equipment bonding jumper is desired.
$
10.75
Qty:
Part #:307995
- Appleton aluminum liquidtight ST Series connectors with plain throat provide a dependable connection for liquidtight flexible metal conduit. Their lightweight aluminum construction facilitates installation. The compact design results in a connector that offers a small turning radius. They seal out oil water dust dirt and fumes.
$
10.75
Qty:
Displaying: 1 - 24 of 50 Matching Items