1/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 1/8in 7/16in
Qty:
Qty:
Part #:504830
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:511845
-
7/16" Wire Rope Clip, Forged Carbon Steel, Galvanized
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:459-10907
- Bondhus® Balldriver® L-Wrench KeysProduct DetailsBall end inserts into a screw at a 25° angle and allows natural hand and wrist movementSaves time by quickly funneling tool into screwSuperior ball end strength and working angleWorks in hard-to-reach places.
Qty:
Qty:
Qty:
Part #:507925
- 1/4" Drive 6-Point SAE 7/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Part #:810266
- 4 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:501590
- 1/2" Drive SAE 5/8" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503701
- Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:134-J9521
-
Drive into end of broken pipe or fitting.
Use tap holder or wrench on extractor to turn out broken part.
Size stamped on extractor refers to drill bit size to be used with that extractor.
Qty:
Part #:811645
- 1/2" Drive 6-Point SAE 7/16" Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Part #:511894
-
7/16" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Part #:802764
- Steel Number Stamp Sets&bull Number sets contain 9 pieces 0 thru 9(the 6 is used as a 9)&bull Crowned striking surface ensures full forceto the center of the stamp & textured shankprovides firm easy grip
Qty:
Qty:
Qty:
Qty:
Part #:812737
- Steel Letter Stamp Sets
&bull Letter sets contain 27 pieces A thru Z plusampersand (&)&bull Tempered shanks for extra safety
Qty:
Qty:
Qty:
Qty:
Qty:
Displaying: 1 - 24 of 58 Matching Items