3/16 in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 3/16 in 9/16in
Part #:502912
-
3/16&rdquo Cold Shut, Steel, Zinc Plated
Connections for Chain and Attachments
When Using Cold Shuts with Chain, Use One Size Larger Than Chain Size
With A Hammer, Drive the Open End Through the Cold Shut Eye. Peen the Extended End to Prevent Opening
Order Unit is "Each"
Note Cold Shuts Should Not Be Reused After Closure Has Been Made
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Qty:
Part #:509044
- Proto 1/2" Drive Extra Long Hex Bit Socket 9/16"
Features and Benefits
Bit holders have a hex opening to hold the bit allowing the bit holder to take the full load of torque.
Made of heat-treated alloy steel.
Polished chrome finish.
Qty:
Qty:
Part #:502805
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:508012
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511937
-
3/16" Wire Rope Thimble, Electro-Galvanized
If Used on Coated Cable, Remove the Coating From the Assembly Area
Follow Assembly Instructions
Qty:
Qty:
Qty:
Part #:811597
- 3/8" Drive 6-Point SAE 9/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:500375
- 9/16" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:503456
- 9/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:134-JSCV18A
-
Anti-Slip Design (ASD) open end.
Smooth transition from head to shank.
Industrial strength I-Beam shank provides broad bearing surface helping improve comfort and helping reduce hand fatigue.
Protected switch lever helps prevent accidental reversal.
Compact ratcheting head improves access.
72 teeth provide 5° ratcheting.
Qty:
Part #:504823
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:504840
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:507840
- 1/2" Drive SAE 9/16" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Qty:
Qty:
Part #:805806
- 3/8" Drive SAE 9/16" Impact Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:811843
- 1/2" Drive SAE 9/16" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Displaying: 1 - 24 of 41 Matching Items